Panasonic GP-KS1000E Benutzerhandbuch

Seite 7

Advertising
background image

-5-

Pin No.

Description

Ground (GND)

1

Ground (GND)

2

Red (R) Output (0.7 V [p-p] /75

)

3

Green (G) Output (0.7 V [p-p] /75

)

4

Blue (B) Output (0.7 V [p-p] /75

)

5

Composite Video Output (1.0 V [p-p] /75

)

6

Sync (SYNC) Output (0.3 V [p-p] /75

)

7

Ground (GND)

8

Ground (GND)

9

!5

Video Output Connector (VIDEO OUT)

A 1.0 V[p-p] composite video signal is provided at
this connector.

!6

Gen-lock Input Connector (G/L IN)

The colour video signal of the camera is automati-
cally synchronized to the gen-lock signal
(Composite Signal, Black Burst Signal or Video
Sync) when either signal is supplied to this connec-
tor.

Caution:

If a camera picture supplied from this

connector, such as a VTR playback picture,
appears jittery on the screen, proper camera
picture synchronization cannot be obtained.

!7

Gen-lock Video 75

Termination On/Off Switch

(75

ON/OFF)

When the gen-lock video signal is looped through
the BNC “T” adopter, set this switch to the OFF
position. If it is not through the BNC “T” adapter, set
this switch to the ON position.

!8

EVR Adjustment Connector

Connect the EVR to this connector.
Normally, keep the connector covered with the rub-
ber cap.

!9

DC 12V Input Terminals (DC 12V IN)

These terminals accept an external DC source sup-
plying nominal power of 12V, 0.7A -1A.

!4

S-Video Output Connector (S-VIDEO OUT)

The luminance (Y) and chroma (C) signals for S-
VHS VTR or monitor are provided at this connector.

Pin Configuration

4

2

3

1

Description

Pin No.

Y Ground (GND)

1

C Ground (GND)

2

Y Signal Output: 0.7 V [p-p] (Y level / 75

)

3

C Signal Output: 0.3 V [p-p] (burst level / 75

)

4

@0

User File Set Indicator

This indicator show the setting steps of the User File
Set as follows:

Setting

Indicator

is on process

Blinks

is completed

Goes off after blinking

is incomplete

Lights up

@1

User File Set Switch

This switch is used to change and memorize the
setting of User File Set Function.

@2

User File Item Switch

This switch is used to select a User File Setting item.
Refer to User File Setting on page 10 for selectable
items..

@3

User File Adjust Control

This switch is used to adjust the value of an item
selected with the User File Item switch.

@4

User File Select Switch

This switch selects the setting of SC Coarse (item
No.1) or the sensing zone (item No.7).

@5

User File Set On/Off Switch

This switch is used to activate the User File Setting
Function. When this switch is set to ON, User File
Item switch @2, User File adjust control @3, and User
File select switch @4 are available to set the User
File Settings Function.

@6

This switch is preset at the factory.

Fix this switch to the OFF position.

@7

PEAK / AVE Switch

This switch is used to select AGC and ELC detec-
tion levels. Set the switch to ON to select PEAK
detection, or to OFF to select AVERAGE detection.
The video level can be changed using the Video
Level Control !1 on the front panel.
Normally, set this switch to OFF.

@8

White Balance Offset On/Off Switch

By turning on this switch, the white balance offset in
the AWC can be adjusted to a fine level by using the
R/B Gain Controls i.
Normally, keep this switch in the ON position.

on
off

on
off

on
off

on
off

Cautions:

• Connect this to a DC 12 V class 2 power supply

only.

• To prevent fire or electric shock hazard, the UL

listed wire VW-1 style 1007 should be used for
the cable for DC 12V Input Terminal.

Advertising