Yamaha CP300 - Handbuch (Seite 122)

Liste der Effektparameter
CP300 Bedienungsanleitung 122
Anhang
WAH+DIST+TEMPO DELAY
WAH+OD+TEMPO DELAY (Variation, Insertion block)
V DIST HARD+TEMPO DELAY
V DIST SOFT+TEMPO DELAY (Variation, Insertion block)
VIBE ROTOR (Variation, Insertion block)
NO EFFECT (Reverb, Chorus, Variation)
THRU (Insert-Block)
* Parameter 10 Dry/Wet betrifft nur Insert-Effekte.
Nr. Parameter Display Wert Siehe
Tabelle
Steue-
rung
1 Delay Time 64th/3 – 4thx6 0 – 19 table #14
2 Delay Feedback
Level -63 – +63 1 – 127
3 Delay Mix 0 – 127 0 – 127
4 Dist Drive 0 – 127 0 – 127
5 Dist Output Level 0 – 127 0 – 127
6 Dist EQ Low Gain -12 – +12dB 52 – 76
7 Dist EQ High Gain -12 – +12dB 52 – 76
8 L/R Diffusion 1 (-63ms) – 64 (0ms) –
127 (63ms) 1 – 127
9 Lag 1 (-63ms) – 64 (0ms) –
127 (63ms) 1 – 127
10 Dry/Wet D63>W – D=W – D<W63 1 – 127 ●
11 Wah Sensitive 0 – 127 0 – 127
12 Wah Cutoff Freq
Offset
0 – 127 0 – 127
13 Wah Resonance 1.0 – 12.0 10 – 120
14 Wah Release 10 – 680mS 52 – 67
15
16
Nr. Parameter Display Wert Siehe
Tabelle
Steue-
rung
1 Overdrive 0 – 100% 0 – 100
2 Device Transistor/Vintage Tube/
Dist1/Dist2/Fuzz 0 – 4
3 Speaker Flat/Stack/Combo/Twin/
Radio/Megaphone 0 – 5
4 Presence 0 – 20 0 – 20
5 Output Level 0 – 100% 0 – 100
6 Delay Time 64th/3 – 4thx6 0 – 19 table #14
7 Delay Feedback
Level -63 – +63 1 – 127
8 L/R Diffusion 1 (-63ms) – 64 (0ms) –
127 (63ms) 1 – 127
9 Lag 1 (-63ms) – 64 (0ms) –
127(63ms) 1 – 127
10 Dry/Wet Balance D63>W – D=W – D<W63 1 – 127 ●
11 Delay Mix 0 – 127 0 – 127
12
13
14
15
16
Nr. Parameter Display Wert Siehe
Tabelle
Steue-
rung
1 Vibrate Speed 0.00Hz – 39.7Hz 0 – 127 table #1
2 Vibrate Depth (AM) 0 – 127 0 – 127
3 Vibrate Depth (PM) 0 – 127 0 – 127
4
5
6
EQ Low Frequency 32Hz – 2.0kHz 4 – 40 table #3
7 EQ Low Gain -12 – +12dB 52 – 76
8 EQ High Frequency 500Hz – 16.0kHz 28 – 58 table #3
9 EQ High Gain -12 – +12dB 52 – 76
10 Dry/Wet Balance D63>W – D=W – D<W63 1 – 127
11
12
13
14 LFO Phase
Difference
-180 – +180deg
(resolution=3deg.) 4 – 124
15 Input Mode mono/stereo 0 – 1
16 Vibrate SW OFF, ON 0 – 1 ●
Nr. Parameter Display Wert Siehe
Tabelle
Steue-
rung
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16