Samsung SD-816B-RPSM Benutzerhandbuch

User's guide, Dvd-rom drive sd-816, Your dvd-rom drive

Advertising
background image

1

Your DVD-ROM Drive

2

3

4

5

8

9

2

1

3

4

5

Before you install the DVD-ROM drive, we strongly recommend that you
check that your setup meets the system requirements listed below.

System Requirements

Upgrading the Firmware Flash Memory

Connecting the Cables

To install your DVD-ROM drive in the PC, proceed as follows.

Installing the DVD-ROM Drive

1

Make sure that the PC is powered off and disconnected from any power source.

2

If necessary, attach a horizontal bracket to both sides of the drive.

3

Remove the cover from a free expansion slot and

install the DVD-ROM drive, as shown in the illustration.

Item

Description

Computer

Intel Pentium

III (

or higher), 350MHz or higher,

128 MB of RAM (or higher) with an IDE interface

Disk space

100 MB minimum

Windows version

Windows 95 OSR2 / 98 / 2000 / ME / XP /
Windows NT 4.0 (or higher)

DVD-ROM DRIVE
SD-816

User's Guide

BG68-00613A Rev.00

Safety Precautions

The following diagrams illustrate the precautions to be taken when using
your DVD-ROM drive.

You must not use the drive in any manner other than that specified in this guide.

Avoid exposing your eyes or skin to direct or scattered radiation.

CAUTION

Do not attempt to repair the DVD-ROM drive yourself. Contact
your dealer or local SAMSUNG representative for all repairs.
If you make any adjustments or perform any operations other
than those specified in this guide, you run the risk of exposure to
hazardous radiation.

WARRANTY

Please refer to the Samsung limited warranty statements.

Precautions

1. To reduce the risk of fire or electric shock, do not expose this

appliance to rain or moisture.

2. Always check each disc for cracks before using it. If there are

cracks on the surfaces, especially around the border of the center
hole, we recommend that you make a copy of the disc
immediately and then stop using it. If you continue using the disc,
it will probably develop more cracks and eventually cause
irreparable damage.

3. Do not use poor quality discs:

From unknown sources

Without any copyright

Scratched or damaged in any way

6

7

Setting Up the Device Driver

Installing the Device Driver

Using the DVD-ROM Drive

Storing and Cleaning Your Discs

Solving Technical Problems

Automatic Setup

Manual Setup

LAST DRIVE = Z
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

C :\SAMSUNG\MSCDEX /D:SSCD000

SAMSUNG continually strives to improve its products.
Both the design specifications and these user instructions are thus subject to change without notice.

Technical Specifications

1. Two-pin digital audio output terminal for use with a sound or

MPEG card supporting digital audio features

2. Four-pin sound output terminal for use with a sound card

(refer to the sound card documentation for further details)

3. Master/slave select terminal

4. 40-pin host IDE interface connector

5. 4-pin power terminal

The product firmware can be upgraded by downloading the updated file from the
following Web site:

http://www.samsung-ODD.com

www.samsungelectronics.com/odd

Use of the brackets depends on your computer
model; you can purchase these accessories
separately from your computer dealer.

1. Power cable
2. Master/slave select terminal

3. IDE cable

4. Audio cable

1

Connecting the power cable
The 4-pin power cable from the internal power unit of your computer must be
connected to the power terminal on the rear of the DVD-ROM drive.

2

Installing a jumper on the master/slave select terminal
Install the jumper in the correct position on the terminal:
MA to use the device in the master mode
SL to use the device in the slave mode
CS to control the device via a CSEL host interface signal

See Step 3 for further details.

3

Connecting the IDE cable

Two configurations are possible.

The DVD-ROM drive is the only IDE device in addition to the hard disk.

4

Connecting the audio cable from a sound card
Connect the 4-pin audio cable between the sound output terminal on the
DVD-ROM drive and the audio input terminal on the sound card.

Install the jumper in the SL position (Slave).
Connect the 40-pin flat IDE cable from the IDE port
on the mother board, first to the DVD-ROM drive

and then to the ha

r

d disk

.

Install the jumper in the MA position (Master).
Connect the 40-pin flat IDE cable from a second
IDE port on the mother board directly to
the DVD-ROM drive or first to another additional
IDE drive and then to the DVD-ROM drive.

IDE port

Mother board

DVD-ROM

(SL)

Hard disk

(MA)

You already have an additional IDE device installed in your computer.

Mother
board

Second IDE cable

DVD-ROM

(MA)

CD-ROM

(SL)

Hard disk

(SL)

Hard disk

(MA)

First IDE cable

1

Insert the setup diskette in the diskette drive and change the directory to A:,
where A: is the diskette drive.

To do so, type A: after the C:\ prompt and press [Enter].

2

Type CDSETUP and press [Enter].

3

Reboot the computer.

1

Make the C:\SAMSUNG directory.

2

Copy the files from the diskette to the C:\SAMSUNG directory.

To do so, type COPY A:

*.*

C:\SAMSUNG after the C:\ prompt and press

[Enter].

3

Edit the CONFIG.SYS file.
Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.

4

Edit the AUTOEXEC.BAT file.
Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.

5

Reboot the computer.

No additional device driver is needed for Windows 95/98/2000/ME/XP/NT, as the
default Windows device driver is used. You can check that the DVD-ROM drive
has been correctly detected by Windows. To do so, proceed as follows.

1

Double-click on the My Computer icon on your desktop.

2

Double-click on the Control Panel folder.

3

Double-click on the System icon.

4

Click on the Device Manager tab.

5

Expand the CD-ROM branch.
The SAMSUNG DVD-ROM SD -

***

device name is displayed.

The SAMSUNG device driver enables discs in the DVD-ROM drive to be read but
not recorded in an MS-DOS environment; the driver is located in the D driver folder
on the CD record utility disc.

DVD Region Protection Coding (RPC):

The RPC feature is supported on DVD players and is used with DVD-video
discs (such as movies). Currently, the motion picture industry has divided the
world into different regions or zones that correspond to the regional markets
into which the motion picture industry releases movies. Simply put, RPC codes
are placed on movies marketed throughout the world, based on the region of
the world in which they are being sold. These RPC codes help control and pre-
vent pirating of new movies into other motion picture regions prior to their true
release dates within those markets.

The SD-816 DVD-ROM drive supports RPC phase II. In the RPC-2 mode,
the local code can be changed by users. RPC-2 is selected by default
for the SD-816 DVD-ROM drive. You can change the region code up to
five times via an MPEG application.

Please contact your dealer or local SAMSUNG representative if you
wish to change the local code more than five times.

To play audio or video CDs in your DVD-ROM drive, proceed as follows.

1

Push the power button and boot the computer.

2

After booting the computer, open the disc
compartment by pressing the Eject button.

3

Insert the disc (CD/DVD) with the label on the
disc facing upwards and close the disc
compartment by pressing the Eject button.

The indicator light comes on.

4

Play the disc (CD/DVD).

1

Do not place a disc in direct sunlight.

2

Store a disc vertically in a well-ventilated and
stable location.

3

Do not write or attach a label on a disc.

4

Do not drop a disc or place heavy objects on it.

5

Do not touch the surface of a disc; hold it by
the edges.

6

To clean a disc, polish lightly from the inside
of the disc to the outside with a soft cotton cloth.

7

Do not leave the disc compartment open
when you are not using it.

Playing Audio CDs

Run the CD player supplied with Windows or your sound card. You can listen to
the CD by connecting headphones to the appropriate connector. If you have
installed the appropriate player, such as Microsoft Windows Media Player, you can
adjust the volume using the headphone volume control on the drive front panel.

Playing Video CDs

Set up and run the SOFT MPEG program.

To ensure a long service life for your discs and drive, follow the precautions
below when storing and cleaning your discs.

Problem

Meaning / Solution

The DVD-ROM drive is not
detected by the computer.

Check that the power, audio and IDE cables are
correctly connected to the computer.

Change the IDE cable and reconnect it to the computer.
Preferably, connect a second IDE cable to the DVD-ROM
drive in master mode.

Check the position of the jumper in the master/slave
select terminal.

Reinstall the device driver or update it with the latest
version by downloading it from the Samsung Web site.

- www.samsung-ODD.com
- www.samsungelectronics.com/odd

This case may occur when there is a Windows
installation problem; reinstall Windows.

Check whether the audio cable is correctly connected
to the sound output terminal on the DVD-ROM drive
and the sound card CD-IN terminal.

Check that the sound card is operational.

Adjust the volume control.

Install the latest version of the device driver.

Check whether the CD is of good quality and clean it,
if necessary.

Check that the power cable is correctly connected.

Power off and disconnect the PC. Insert a pin or
unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.

Adjust the size of the replay screen.

After checking the display resolution, adjust it,
if necessary.

The computer may not recognize the disc if you start
playback too quickly after inserting the disc.
Open and close the disc compartment and try again.

Clean the disc and try again.

The interface mode of the sound card is AT-BUS.
You must therefore connect the DVD-ROM drive to
the IDE port on the PC mother board, rather than to
the sound card, or install an IDE-compatible sound
card.

After installing the DVD-ROM
drive, the PC gets slower.

The DVD-ROM drive is not

recognized by MS-DOS.

The DVD-ROM drive is not
detected by Windows.

No sound is heard from an
audio CD.

A CD is not read or is read
too slowly.

The disc compartment will
not open.

When the MPEG software plays a
Video CD, the pictures are not
regular and the running speed is
too slow.

The Disc is not in message is
displayed even though a disc
has been inserted.

The DVD-ROM drive is not
detected after it is connected
to a sound card.

Sustained :

Max. 21,600KB/sec (16X) / Max. 7,200KB/sec (48X)

DISC

ERROR RATE

REAR PANEL

FRONT PANEL

OPERATING
ENVIRONMENT

GENERAL

RELIABILITY

DRIVE
PERFORMANCE

Disc diameter

Disc types supported

Data transfer rate

Access time(Random)

Data buffer capacity

Laser

Slide mechanism

Spindle motor

Loading mechanism

Eject button

Indicator(LED)

Headphone output

Volume control

Dimensions

Net weight

Operation

Storage

Required power

Interface connector

Audio output

Jumper block

MTBF

DVD-ROM, DVD-VIDEO, DVD-R, DVD-RW, DVD-RAM, CD-DA(Audio),
CD-ROM, CD-ROM XA, CD-Plus, CD-Extra, Photo-CD(Single,Multi-session),
Video CD ready, Enhanced CD, CD-I/FMV, CD-R, CD-TEXT, CD-RW

120mm or 80mm

PIO Mode 4

: 16.6MB/sec

Multiword DMA mode 2 : 16.6MB/sec
UDMA mode 2

: 33MB/sec

512KB

Semiconductor Laser

Stepping motor

Brushless motor

Tray. DC motor(Soft Eject). Horizontal/Vertical

Auto eject or Auto inject

BUSY

Stereo mini-jack(Ø3.6mm) 0.60V±20%(rms) 33

Wheel knob

+5VDC : 2.0A, +12VDC : 1.0A

ATAPI

Line out 0.7V

±

20%(rms) : 47K

Device configuration jumper

Temperature :

5 ~ 45°C,

Humidity : 10 ~ 80%

Temperature : -25 ~ 60°C,

Humidity : 10 ~ 90%

148.2(W) x 42(H) x 184(D)mm (including Bezel)

740g

125,000 POH(Duty 20%)

10

-15

/ MODE1:10

-12

, MODE2:10

-9

95ms

100ms

ITEM

SD-816

DVD

CD

* In case of the PC without UDMA, it may have a different DVD data transmission rate.

* This product has been set at the UDMA mode. It may cause trouble due to

the compatibility of a specific board or system. In this case, download the latest
version of “Firmware” which supports the DMA Mode.
Using the DMA mode may slightly decrease the efficiency of DVD-ROM.

FCC Compliance

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
deter-mined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures :

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

1. Connector for stereo headphones with a 3.6 mm stereo mini-jack

2. Headphone volume control

3. Disc compartment (the compartment opens and closes automatically

when you press the Eject button)

4. Emergency eject hole (if the compartment does not open when you

press the Eject button, power off the computer, insert a pin or unfolded

paper clip in the hole and push firmly)

5. Indicator light (when it is green, a disc is being read)

6. Eject button

http://www.samsung-ODD.com

www.samsungelectronics.com/odd

1

2

3

4

5 6

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment

If you have no free expansion slot,
install the drive in place of the
diskette drive.

DVD-ROM
Drive

COVER

Advertising
Dieses Handbuch ist für die folgenden Produkte bezogen werden: