2, sequencer-data recepìion^ransmission – Yamaha DOU-10/MDP2 Benutzerhandbuch

Seite 30

Achtung! Der Text in diesem Dokument wurde automatisch erkannt. Um das ursprüngliche Dokument anzeigen, können Sie den "ursprünglichen Modus" verwenden können.

Advertising
background image

(19) Pilch Bend Sensitivity

RPN

Data entry

MSB LSB MSB LSB
(ЮН ООН mmH xxH; ООН, OOH-lflH, ООН

mmsControl value
XX >Not recognized
Initial valuel02H-OOHl

(20) Fine Tuning

RPN

Data entry

MSB LSB MSB LSB
ООН OlH mmH IlH: ООН, OOH-7FH, 7FH

mm»Uppef byte of control value

II »Lower byte of control value
Initial value|40H,(X)H|

(21) Coarse Tuning

RPN

Data entry

MSB LSB MSB LSB

ООН 02H mmH xxH:28H, OOH-S8H, ООН

mm»Control value
XX »Not recognized
Initial value[40H, 00H|

5) Program Change

Status byte 2nd byte
CnH

ppH

n »MIDI channel
pp»Program number
Initial value |(X)H|

6) Channel Preawre

Status byte 2nd byte
DnH

wH

:OH-FH(ch1,<h.l6)
:00H-7FH(0-127)

:0H-FH(ch1.-ch.)6)

:00H-7FH(0-127)

n »MIDI Channel

w »Channel pressure

Initial value |00H|
This controls rrtodulation In the CM mode.
Not received in the doc mode.

7)PHchBend

Status byte 2nd byte
EnH IlH

n »MIDI Channel
mm»Plich bend MSB
II »Pitch bend LSB
Initial value |40H,00H)

3rd byte

:0H-FH(ch l.<h.l6)
:00H.7FH (0-127)
:00H-7FH (0-127)

1.2 Channel Mode MeieagM

(1) All Sound Off

Status byte 2nd byte
BnH

7BH

n »MIDI еЗгаппе!
xK»Not recognized

(2) Reeet ^1 Controllen

3rd byte
xxH

:0H-FH (ch1.-ch.16)

Status byte 2nd byte

BnH

79H

3rd byte
xxH

n

»MIDIChannel:OH-FH(chl.-ch.l6)

XX »Not recognized

The settings of the controllers below change when this
Controller

Pitch bend

Channel pressure
Modulation

Expression
Sustain

Sostenuto
Softdn Doc rrrode)
NRPN
RPN

Value

14OH,0OHJ
iOOHj
iOOH]
Ì7FHI
lOOHI
lOOHI
lOOH!
|7FH,7FH]
|7FH,7FH]

Resets legato control settirrg.

(3) All Note Off

Status byte 2nd byte
BnH ' 7BH

3rd byte
xxH

n»MIDI Channel: 0H-FH(ch 1.-ch.16)
xx»Not recognized

1.3 System Exclusive Messages

1) DOC on

FOH, 43H, 73H, 01H. 14H, F7H

2} Reverb Type

FOH, 43H, 73H, Ot H, n H, Of H, 59H, nnH, F7H

nn» Reverb type:

ООН »off

01H»Room
02H»Hall1
03H»Hall2
04H»Cosmic

3) Reverb Depth On (for each charnel)

FOH, 43H, 73H, 01H, 1BH, F7H

Not received in CM mode.

4) Master Tuning

FOH, 43H, IxH, 27H,30H,OOH, ООН, xmH, xlH,

xxH, F7H

X, XX

»Not recognized

m »Tuning MSB

I »Tuning LSB

5) CM System On

FOH, 7EH, 7FH, 09H, 01H, F7H

6) Matter Volume

FOH, 7FH, 7FH, 04H, 01H, II, xx, mm, F7H

mm »Master volume
XX »Not recognized

Not received in doc mode.

2, Sequencer-Data Recepìion^ransmission

2.1 Channel Messages

All channel messages are recorded and played back.

8nH, kkH, wH
9nH, kkH, wH
AnH, kkH, wH
BnH, nnH, wH
CnH, ppH
DnH, wH
EnH, llH, mmH

Note of(
Note cm
Polyphonic key pressure

Control change

Program change

Channel pressure

Pitch bend

2.2 System Exclusive Messages

All System Exclusive messages are recorded

FOH................... F7H

2.3 System Common Messages

DMIDI Time Code

F)H, ndH

Not received

2) Song Position Pointer

F2H, IlH, hhH Song Position Pointer

when Remote In Setting Is on, under the condition of STOP or Play Pause, it will receive messages properly

and become paused condition.

3) Song Select

F3H, ssH

Song select

Not received

4) Tune Request

F6H

Tune request

Not received

2.4 Real Time Messages

1) Timing Clock

F6H

Received when set to external synchronization.

While it playing back or recording, it wilt send messages.

2) Start/Continue/Stop

FAH Start
F6H Continue
FCH Stop

When Remote Out Setting is on, it will send messages.
When FA, FB Remote In Setting is on while using STOP or Play Pause function it will receive messages.
When FC Remote in Setting is on while it playing back, it will receive messages.

3) Active Sensing

FEH

Received and transmitted.

This message is transmitted automatically every 250 ms.lf not received for 500 ms (after receiving an FEH
message), "All note off" and "Reset all controllers" messages are sent to the internal tone generator.

28

Advertising
Dieses Handbuch ist für die folgenden Produkte bezogen werden: