Dynacord DSA 8805 - Handbuch (Seite 34)

DIGITAL SYSTEM AMPLIFIER
34 Owner‘s Manual / Bedienungsanleitung
DSA 8410
Amplifier at rated conditions, all channels driven, rated loads, unless otherwise specified.
1) Output Mode 2
Ω
(1000 W at 2
Ω
, 500 W at 4
Ω
, 250 W at 8
Ω
)
2) Output Mode 4
Ω
(1000 W at 4
Ω
, 500 W at 8
Ω
)
3) Output Mode 70 V
4) Output Mode 100 V
5) Depending on the ambient temperature, the unit might reduce the output power at 2
Ω
load
6) 50 Hz High Pass is automatically activated in 70 V / 100 V output mode
7) 140 V at 10
Ω
8) 200 V at 20
Ω
9) Due to the mains voltage situation in Japan the values for the maximum output power can be decreased by 15%
10) Depth of the unit without rack ears (detachable): 380 mm
Load Impedance
Low Impedance Mode High Impedance Mode
2 Ω 1 4 Ω 2 8 Ω 2 70 V / 5 Ω 3 100 V / 10 Ω 4
Maximum Midband Output Power
THD = 1%, 1 kHz, 4 channels driven
1000 W 5 1000 W
500 W
VLD: 1000 W
1000 W 1000 W
Rated Output Power
THD < 0.3%, 20 Hz 6 ...20 kHz, 4 ch. driven
900 W 900 W
450 W
VLD: 900 W
900 W 900 W
Maximum Bridged Output Power
THD= 1%, 1 kHz
- 2000 W 1 2000 W 2000 W 7 2000 W 8
Maximum RMS Voltage Swing
THD = 1%, 1 kHz
45 V 63 V
63 V
VLD: 89 V
70 V 100 V
Power Bandwidth
THD = 1%, ref. 1 kHz, half power @ rated load
10 Hz...25 kHz 50 Hz...25 kHz
Voltage Gain, ref. 1 kHz 32 dB 32 dB 32 dB 33 dB 36 dB
Input Sensitivity, rated power, 1 kHz 1.1 V
(+3.0 dBu)
1.55 V
(+6.0 dBu)
1.55 V
(+6.0 dBu)
1.55 V
(+6.0 dBu)
1.55 V
(+6.0 dBu)
THD at rated output power, MBW = 80 kHz, 1 kHz < 0.05%
IMD-SMPTE, 60 Hz, 7 kHz < 0.05%
DIM30, 3.15 kHz, 15 kHz < 0.02%
Maximum Input Level +22 dBu (9.76 V
rms
)
Crosstalk, ref. 1 kHz, at rated output power < -80 dB
Frequency Response, ref. 1 kHz, 8 Ω load
15 Hz 6 ...30 kHz (±1 dB)
Input Impedance, active balanced 20 k Ω
Damping Factor, 1 kHz, 8 Ω > 240
Slew Rate 28 V/ μs
Signal to Noise Ratio Amplifier, A-weighted 101 dB 103 dB 103 dB 104 dB 106 dB
Output Noise, A-weighted < -66 dBu < -65 dBu < -65 dBu < -65 dBu < -64 dBu
Output Stage Topology Class D
Power Requirements (factory configured) 220-240 V, 50-60 Hz or 120 V, 50-60 Hz or 100 V 9 , 50-60 Hz
Power Consumption, 1/8 maximum output power 840 W
Protection Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Inrush
Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/Under-
voltage Protection
Cooling Front-to-Rear, temperature controlled fans
Ambient Temperatur Limits +5 °C...+40 °C (40 °F...105 °F)
Safety Class I
Dimensions (W x H x D), mm 481 x 88.0 x 421 10
Weight 11.1 kg (24.3 lbs)
Optional:
Rear-rackmount
D113223 (RMK-15)