Indesit XWDE-861480X-W-DE - Handbuch (Seite 22)

22
GB
How to run a wash cycle or a
drying cycle
Rapid programming
1. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
2. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the relevant
compartments as described in “Detergents and laundry”.
3. CLOSE THE DOOR.
4. Press the “PUSH&WASH+DRY” button to start the
programme.
Traditional programming
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the relevant
compartments as described in “Detergents and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons:
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the 8 programme is selected, the
temperature can be increased up to a value of 90°C.
Setting the drying cycle a
The first time the button is pressed, the machine will
automatically select the maximum drying cycle which is
compatible with the selected wash cycle. Subsequent
presses will decrease the drying level and then the drying
time, until the cycle is excluded completely (“OFF”).
Drying may be set as follows:
A- Based on the desired laundry dryness level:
Cupboard : suitable for laundry which can be put
back in a cupboard without being ironed.
Hanger : ideal for clothes which do not need to be
dried fully.
Iron : suitable for clothes which will need ironing
afterwards. the remaining dampness softens creases,
making them easier to remove.
B - Based on a set time period: between 210 and 30 minutes
If your laundry load to be washed and dried is much
greater than the maximum stated load (see adjacent
table of wash cycles), perform the wash cycle, and when
the cycle is complete, divide the garments into groups
and put some of them back in the drum. At this point,
follow the instructions provided for a “Drying only” cycle.
Repeat this procedure for the remainder of the load.
Note: a cooling-down period is always added to the end
of each drying cycle.
Drying only
Press button to perform the drying-only cycle.
After selecting the desired cycle (compatible with the type
of garments), press button to exclude the washing
phase and start the drying phase at the maximum level
for the selected cycle. The drying level or time may be set
and changed by pressing the drying button .
(Not compatible with cycles 13 and 14).
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Modify the cycle settings.
• Press the button to enable the option; the indicator
light corresponding to the button will switch on.
• Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with another
previously selected option, the indicator light will
flash accompanied by a buzzer (3 beeps), and only
the latter option will be activated; the indicator light
corresponding to the activated option will turn on.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/PAUSE
button. The corresponding indicator light will turn green,
remaining lit in a fixed manner, and the door will be locked
(the DOOR LOCKED symbol will be lit). To change a
wash cycle while it is in progress, pause the washer-
dryer using the START/PAUSE button (the START/PAUSE
indicator light will flash slowly in an amber colour); then
select the desired cycle and press the START/PAUSE
button again. To open the door while a cycle is in progress,
press the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press the
START/PAUSE button again to restart the wash cycle from
the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.