Kemo Electronic B092 Benutzerhandbuch
Seite 2
Donnés technique:
Kit: pour être soudés par vous-même | Tension de service: 6 - 12 V/DC
| Consommation de courant: aprox. 20 mA | Fréquence de clignote-
ment: ajustable | Dimensiones de plaquette: aprox. 26 x 25 mm
Ota huomioon LED:in oikea asennus. “K“-napa on vähän litistetty (katso kuva).
Trimmeripotentiometrillä voi säätää vilkkumistaajuuden.
Tekniset tiedot:
Pakki: juote itse | Käyttöjännite: 6 - 12 V/DC | Virrantarve: aprox. 20
mA | Vilkkumistaajuus: säädettävä | Piirilevyn koko: n. 26 x 25 mm
Let vooral op de juiste inbouw van de LED´s. De “K“-aansluiting is iets afgev-
lakt (zie tekening). Met de instelpotentiometer kan de knippersnelheid inge-
steld worden.
Technische gegevens:
Uitrusting: het soldeer zelf | Bedrijfsspanning: 6 - 12 V/DC | Stroo-
mopname: aprox. 20 mA | Knipperfrequentie: verstelbaar |
Print plaat
afmeting:
ca. 26 x 25 mm
Tenha o cuidado de montar os leds correctamente. O terminal “K“ tem um lado
ligeiramente achatado (ver a figura). Com a ajuda do potenciometros ajustável
é possível ajustar a velocidade do efeito.
Dados técnicos:
Kit: para ser soldada por si mesmo! | Tensão de serviço: 6 - 12 V/DC |
Consumo de corrente: cerca. 20 mA | Intermitente de frequência: ajus-
tável |
Medida da placa de circuito:
ca. 26 x 25 mm
Bitte achten Sie auf den richtigen Einbau der LED‘s. Der “K“-Anschluss ist
leicht abgeflacht (siehe Zeichnung). Mit dem Trimmpotentiometer kann die
Blinkgeschwindigkeit eingestellt werden.
Technische Daten:
Bausatz: Zum selber löten | Betriebsspannung: 6 - 12 V/DC | Strom-
aufnahme: ca. 20 mA | Blinkfrequenz: justierbar | Platinengröße:
ca. 26 x 25 mm
Please take special care mounting the LED‘s correctly. The “K“-connection
has been slightly flattened (see figure). With the aid of the trimmer poten-
tiometer it is possible to adjust the flashing velocity.
Technical Data:
Kit: To solder yourself | Operating voltage: 6 - 12 V/DC | Power con-
sumption: approx. 20 mA | Flashing frequency: adjustable | Board
dimensions: approx. 26 x 25 mm
Por favor, observe Vd. la instalación correcta de los LED‘s. La conexión “K“
es un poco aplanada (mire el dibujo). La velocidad de intermitencias se
puede regular con el potenciómetro de ajuste.
Datos técnicos:
Kit: a soldarse por usted mismo | Tension de service: 6 - 12 V/DC |
env. 20 mA | Fréquence de clignotement: ajustable | Dimensiones
de la placa: aprox. 26 x 25 mm
Veiller au montage correct des leds. Le branchement “K“ (cathode) est
légèrement aplati (voir schéma). Le potentiomètre permet de régler la
fréquence d‘allumage.
MONTAGEBEISPIEL | INSTALLATION EXAMPLE
D | Entsorgung:
Wenn das Gerät entsorgt werden soll, darf es nicht in den Haus-
müll geworfen werden. Es muss an Sammelstellen für Fernseh-
geräte, Computer usw. entsorgt werden (bitte erkundigen Sie
sich in Ihrem Gemeindebüro oder in der Stadtverwaltung nach
Elektronik-Müll-Sammelstellen).
GB | Disposal:
This device may not be disposed with the household waste. It has to be
disposed at collecting points for television sets, computers, etc. (please ask
your local authority or municipal authorities for these collecting points for
electronic waste).
D | Wichtig: Bitte beachten Sie die extra beiliegenden “Allgemeingülti-
gen Hinweise” in der Drucksache Nr. M1003. Diese enthält wichtige Hin-
weise der Inbetriebnahme und den wichtigen Sicherheitshinweisen! Diese
Drucksache ist Bestandteil der Beschreibung und muss vor dem Aufbau
sorgfältig gelesen werden.
GB | Important: Please pay attention to the “General Information” in
the printed matter no. M1003 attached in addition. This contains impor-
tant information starting and the important safety instructions! This printed
matter is part of the product description and must be read carefully before
assembling!
GB
FIN
E
D
F
NL
P
BAUTEILE | COMPONENTS
Elko | Elca
100 μF
Elko | Elca
10 μF
Diode
1N4006
Widerstände | Resistors
620 Ω
Widerstände | Resistors
12K
Trimmpoti
20K
Platine | Board
Maße | Dimensions ca. 26 x 25 mm
Transistor
BC 546B
1x
2x
2x
1x
1x
2x
2x
1x
1x
1x
blue-red-brown...
brown-red-orange...
Aufdruck | Overprint C546B
Ersatz | replacement BC 547B,
BC548B
Aufdruck | Overprint 1N4006
Ersatz | replacement 1N4007
Aufdruck | Overprint 203
16 V
16 V
LED
rot | red
5 mm
LED
gelb | red
5 mm
T1 / T2
LED 1
LED 2
C4 / C5
R1 / R4
R2 / R3
D1
C1
P1