Clearaudio (MM) MOVING MAGNET V2 - Handbuch (Seite 2)

Assembly instructions of the MM V2 cartridges:
Before mounting the cartridge the plastic stylus guard should be leaved on the cartridge. Mount the
cartridge using the supplied mounting hardware without over-tightening to allow final adjustment later.
Please be very careful at mounting!
Electrical connections (rear view):
At the rear of the cartridge there are terminal pins for the left and right channels.
Connect the tonearm wires to the cartridge terminal pins as follows:
Attention:
Never braze the tonearm wires to the cartridge terminal pins as this could permanently damage the internal
circuits and your warranty will be void! Only use original cartridge connectors! If your tonearm wiring is not
fitted with these or if they are damaged they are available from your local dealer
(eg. clearaudio cartridge-connectors: Art.-Nr.: CO 011).
Adjustment:
Before final adjustment of the cartridge please follow the set-up procedure recommended by the
turntable or tonearm manufacturer. Set the tracking force carefully within the appropriate range
shown in the data sheet. Incorrect tracking force will lead to distortion and could seriously
damage both stylus and record.
When stylus overhang and anti-skating are precisely adjusted the cartridge can be finally
tightened into final position.
Maintenance:
 Always clean your records before playing.
 Regularly clean the stylus with an appropriate cleaning fluid. This should be available at your
dealer (eg. clearaudio cleaning fluid: Art.-Nr.: AC 003).
 Have the stylus checked after approximately 500 hours. Damaged or worn diamond tip can
cause permanent damage to your records.
Stylus replacement:
After approximately 2000 hours of use (or earlier if you suspect excessive use) the stylus should
be replaced.
Caution: Never try to remove the stylus assembly yourself! For replacement contact your local
dealer.
Techn. Daten - technical
data Concept V2 Performer V2 Artist V2 Virtuoso V2 Maestro V2
Übertragungsbandbreite
Frequency Response
20Hz-20kHz 20Hz-20kHz 23Hz-20kHz 20Hz-20kHz 20Hz-20kHz
Ausgangsspannung (1kHz,
5cm/s) Output Voltage
 3.3 mV  3.3 mV  3.6 mV  3.6 mV  3.6 mV
Kanaltrennung (1kHz)
Channel Separation
> 20 dB > 20 dB > 24 dB > 30 dB > 30 dB
Kanalbalance (1kHz)
Channel Balance
 2 dB  1,5 dB  0,8 dB  0,2 dB  0,2 dB
Abtastfähigkeit
Tracking Ability
80 µm 80 µm 80 µm 90 µm 90 µm
Auflagegewicht
(empf. 1,8 -2,6 g)
Tracking Force (rec. 1.8 - 2.6 g)
2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g
Spulenimpedanz (1kHz)
Coil Impedance
0,66 k  0,66 k  0,66 k  0,66 k  0,66 k 
Spuleninduktivität
Coil Inductance
0,42 H 0,40 H 0,40 H 0,40 H 0,42 H
Lastwiderstand
Load Resistance
47 k  47 k  47 k  47 k  47 k 
Kapazitive Last
Load Capacitance
100 pF 100 pF 100 pF 100 pF 100 pF
Nadelträger
Cantilever
Aluminium Aluminium Aluminium Aluminium Bor / HD
Diamond
Gewicht / Weight 8.4 g 8.4 g 8.4 g 8.4 g 8.4 g
Assembly instructions of the MM V2 cartridges:
Before mounting the cartridge the plastic stylus guard should be leaved on the cartridge. Mount the
cartridge using the supplied mounting hardware without over-tightening to allow final adjustment later.
Please be very careful at mounting!
Electrical connections (rear view):
At the rear of the cartridge there are terminal pins for the left and right channels.
Connect the tonearm wires to the cartridge terminal pins as follows:
Attention:
Never braze the tonearm wires to the cartridge terminal pins as this could permanently damage the internal
circuits and your warranty will be void! Only use original cartridge connectors! If your tonearm wiring is not
fitted with these or if they are damaged they are available from your local dealer
(eg. clearaudio cartridge-connectors: Art.-Nr.: CO 011).
Adjustment:
Before final adjustment of the cartridge please follow the set-up procedure recommended by the
turntable or tonearm manufacturer. Set the tracking force carefully within the appropriate range
shown in the data sheet. Incorrect tracking force will lead to distortion and could seriously
damage both stylus and record.
When stylus overhang and anti-skating are precisely adjusted the cartridge can be finally
tightened into final position.
Maintenance:
 Always clean your records before playing.
 Regularly clean the stylus with an appropriate cleaning fluid. This should be available at your
dealer (eg. clearaudio cleaning fluid: Art.-Nr.: AC 003).
 Have the stylus checked after approximately 500 hours. Damaged or worn diamond tip can
cause permanent damage to your records.
Stylus replacement:
After approximately 2000 hours of use (or earlier if you suspect excessive use) the stylus should
be replaced.
Caution: Never try to remove the stylus assembly yourself! For replacement contact your local
dealer.
Techn. Daten - technical
data
Concept V2 Performer V2 Artist V2 Virtuoso V2 Maestro V2
Übertragungsbandbreite
Frequency Response
20Hz-20kHz 20Hz-20kHz 23Hz-20kHz 20Hz-20kHz 20Hz-20kHz
Ausgangsspannung (1kHz,
5cm/s) Output Voltage
 3.3 mV  3.3 mV  3.6 mV  3.6 mV  3.6 mV
Kanaltrennung (1kHz)
Channel Separation
> 20 dB > 20 dB > 24 dB > 30 dB > 30 dB
Kanalbalance (1kHz)
Channel Balance
 2 dB  1,5 dB  0,8 dB  0,2 dB  0,2 dB
Abtastfähigkeit
Tracking Ability
80 µm 80 µm 80 µm 90 µm 90 µm
Auflagegewicht
(empf. 1,8 -2,6 g)
Tracking Force (rec. 1.8 - 2.6 g)
2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g
Spulenimpedanz (1kHz)
Coil Impedance
0,66 k  0,66 k  0,66 k  0,66 k  0,66 k 
Spuleninduktivität
Coil Inductance
0,42 H 0,40 H 0,40 H 0,40 H 0,42 H
Lastwiderstand
Load Resistance
47 k  47 k  47 k  47 k  47 k 
Kapazitive Last
Load Capacitance
100 pF 100 pF 100 pF 100 pF 100 pF
Nadelträger
Cantilever
Aluminium Aluminium Aluminium Aluminium Bor / HD
Diamond
Gewicht / Weight 8.4 g 8.4 g 8.4 g 8.4 g 8.4 g
Assembly instructions of the MM V2 cartridges:
Before mounting the cartridge the plastic stylus guard should be leaved on the cartridge. Mount the
cartridge using the supplied mounting hardware without over-tightening to allow final adjustment later.
Please be very careful at mounting!
Electrical connections (rear view):
At the rear of the cartridge there are terminal pins for the left and right channels.
Connect the tonearm wires to the cartridge terminal pins as follows:
Attention:
Never braze the tonearm wires to the cartridge terminal pins as this could permanently damage the internal
circuits and your warranty will be void! Only use original cartridge connectors! If your tonearm wiring is not
fitted with these or if they are damaged they are available from your local dealer
(eg. clearaudio cartridge-connectors: Art.-Nr.: CO 011).
Adjustment:
Before final adjustment of the cartridge please follow the set-up procedure recommended by the
turntable or tonearm manufacturer. Set the tracking force carefully within the appropriate range
shown in the data sheet. Incorrect tracking force will lead to distortion and could seriously
damage both stylus and record.
When stylus overhang and anti-skating are precisely adjusted the cartridge can be finally
tightened into final position.
Maintenance:
 Always clean your records before playing.
 Regularly clean the stylus with an appropriate cleaning fluid. This should be available at your
dealer (eg. clearaudio cleaning fluid: Art.-Nr.: AC 003).
 Have the stylus checked after approximately 500 hours. Damaged or worn diamond tip can
cause permanent damage to your records.
Stylus replacement:
After approximately 2000 hours of use (or earlier if you suspect excessive use) the stylus should
be replaced.
Caution: Never try to remove the stylus assembly yourself! For replacement contact your local
dealer.
Techn. Daten - technical
data
Concept V2 Performer V2 Artist V2 Virtuoso V2 Maestro V2
Übertragungsbandbreite
Frequency Response
20Hz-20kHz 20Hz-20kHz 23Hz-20kHz 20Hz-20kHz 20Hz-20kHz
Ausgangsspannung (1kHz,
5cm/s) Output Voltage
 3.3 mV  3.3 mV  3.6 mV  3.6 mV  3.6 mV
Kanaltrennung (1kHz)
Channel Separation
> 20 dB > 20 dB > 24 dB > 30 dB > 30 dB
Kanalbalance (1kHz)
Channel Balance
 2 dB  1,5 dB  0,8 dB  0,2 dB  0,2 dB
Abtastfähigkeit
Tracking Ability
80 µm 80 µm 80 µm 90 µm 90 µm
Auflagegewicht
(empf. 1,8 -2,6 g)
Tracking Force (rec. 1.8 - 2.6 g)
2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g 2.2 g ± 0.3 g
Spulenimpedanz (1kHz)
Coil Impedance
0,66 k  0,66 k  0,66 k  0,66 k  0,66 k 
Spuleninduktivität
Coil Inductance
0,42 H 0,40 H 0,40 H 0,40 H 0,42 H
Lastwiderstand
Load Resistance
47 k  47 k  47 k  47 k  47 k 
Kapazitive Last
Load Capacitance
100 pF 100 pF 100 pF 100 pF 100 pF
Nadelträger
Cantilever
Aluminium Aluminium Aluminium Aluminium Bor / HD
Diamond
Gewicht / Weight 8.4 g 8.4 g 8.4 g 8.4 g 8.4 g
Left output (L+)  white
Left ground  blue
Right output (R+)  red
Right ground  green
Left output (L+)  white
Left ground  blue
Right output (R+)  red
Right ground  green
Left output (L+)  white
Left ground  blue
Right output (R+)  red
Right ground  green