Studiologic CMS 61 - Handbuch (Seite 9)

12
I N S T R U C T I O N S M A N U A L
1.
2.
3.
4.
13
I N S T R U C T I O N S M A N U A L
TECHNICAL
CHARACTERISTICS
CONNECTIONS
PROGRAM
CHANGE
CONTROL#
COMMANDS
BANK
CHANGE
BASE CHANNEL
TOP PANEL
ongratulations on purchasing the Computer Music Station CMS-61 and welcome to the world
of FATAR Keyboard Controllers.
The CMS-61 is the perfect choise of the musician looking for a simple yet versatile keyboard
conroller to produce quality results in the multi-media environment.
The CMS-61 is the only keyboard controller on the market today to accomodate a computer
keyboard and mouse pad within the same product.
• 61 unweighted keys
• One zone
• Velocity Sensitive
• Pitch Bend Wheel and Programmable Wheel
• Two Parallel MIDI Outputs
• Sustain Input Jack
• Volume Input Jack
• Program change, MIDI Channel, Transpose, Programmable wheel (Volume, Pan, Aftertouch,
Pitch, Modulation) etc.
• External Adapter 9V DC 500ma included
• Dimensions: 51 3/4" X 13 3/4" X 4 1/2" 48 lbs.
Connect the AC/DC adapter cable to the power input jack, in the back of the controller, located
next to the power switch.
Make sure that the AC/DC adapter corresponds to the correct voltage output. The CMS - 61 will
accept an adapter that has a rating of 9V DC with a positive polarity tip and has a minimum
current of 200 mA.
Connect MIDI cable from the CMS - 61 MIDI outputs, (each output can handle up to four
synthesizers, modules, or effect devices) to the MIDI input on your sound sources. Set your
sound sources to the desired MIDI channelsby the CMS - 61. Each channel would normally be
assigned to a different sound or effect. Since the CMS - 61 has only one zone, you can only
program one of the 16 channels at a time. Make sure that your sound source is properly assigned
to the channel you are sending on.
To select a base channel hold the [CHANNEL[ switch and enter the channel number (l through
16) by depressing the appropriate black numbered key (0-9). The function switch must be
released after the black number keys. At this point the CMS - 61 is sending on that channel.
A program change command allows you to change the sound on your sound source from the
CMS - 61. The program change will be sent on whichever MIDI channel the CMS - 61 is
currently set. Program changes are numbered 1 through 128. You may notice, depending on the
sound source, that a program change of 1 will show up on your sound source as 0. This is not a
problem, since MIDI is not completely standard between manufacturers. Thank the heavens that
there are only a few anomalies like this between the manufacturers.
To issue a program change, hold the [PROGRAM] switch and enter the desired number on the
numbered black keys with the appropriate program number or use the [INC]/ [DEC] (increment/
decrement) keys. If a number greater than 128 is entered, it will wrap around to the beginning.
Some sound sources today, especially found on computer sound cards, have a feature called
bank select. The MIDI specification calls for bank numbers 1 through 16384. Once you have
selected your bank you are able to select a program change (l through 128).
To select a bank of prograrns, hold the [PROGRAM ]switch, press [BANK] key, and enter the
appropriate bank number using the O through 9 keys. The bank command will be transmitted
when the [PROGRAM] switch is
released. The [INC]/ [DEC] keys may be used instead of entering the bank number.
There are 127 controller functions that are made up of continuous and switch control
commands. See Figure # 3. The most commonly used controllers are aftertouch, pitch,
modulation, volume and pan. Many expensive keyboard controllers offer aftertouch, which
allows expressive control of sound sources. The CMS - 61 allows the same expression via
[WHEEL A]. Aftertouch, pitch,
(1 through 16). Refer to the sound source s owners manual for this procedure.
Connect a momentary footswitch, which circuit is normally open, to the sustain input jack clearly
marked SUSTAIN located next to the MIDI jacks. We recommend a VFP-1/10 (piano-like sustain
pedal) available from Music Industries Corp.
Connect a control voltage pedal for volume in the jack clearly marked VOLUME located next to
the sustain jack. We recommend a VP-26 (expression pedal) available from Music Industries
Corp.
Once all connections are in place, press the power switch to the ON position.
See Figure #2. You will notice on the left a dedicated pitch and a programmable second wheel,
rnarked [WHEEL A]. With [WHEEL A] you may assign aftertouch, pitch, modulation, volume and
pan as well as any controller (O - 127).
To the right of the wheels there are four switches. These switches are used for program change,
channel assignment, transposition and programmable wheel assignment. Eighteen black keys on
the keyboard are used for special MIDI functions. The first five are used for [WHEEL A]. Notice,
[AFT], [PITCH], [MOD], [VOL] and [PAN]. These keys represent aftertouch, pitch, modulation,
volume and panning. The next 10 black keys represent a numeric key pad for program changes
and channel assignments. The following two black keys are used for increment and decrement
of a program change. [INC]/[DEC] will also change the controller number. The last key is used for
selecting a bank. More on this in the next section.
Operation:
Getting around the CMS - 61 is very simple. However, you must know certain basic MIDI theory
before it can make sense.
There are l6 different channels in the MIDI specification that can be accessed modulation,
volume and pan can be accessed by the corresponding black keys, ,while all the remaining
control functions can be accessed by the number or [INC]/[DEC] keys.