ADS-TEC IRF2000 Quick Start Guide - Handbuch (Seite 2)

Quick Start Guide Commissioning /Mounting IRF2000 series
1
120627_ Q UICK S TART GUIDE IRF2000_DE_EN DZ-HAND-91056-0 V1.1 © ads-tec GmbH • Raiffeisenstr.14 • 70771 Leinfelden-Echterdingen
1. Scope of delivery 3. Connecting the device
1 x Industrial Router Firewall
1 x 3 pol. connector
2 x 4 pol. connector
1 x Rail mounting holder
2 x M4 x 6 Pan Head screw + 2 x M4 washer + 2 x Disk washer
4 x rubber feet
1 xEthernet cable 1m
1 x Quick Start Guide Commissioning /Mounting IRF2000 series
1 x GNU General Public License
Warning:
Any installation works on the device are only
permitted if the power supply is switched off, and
if handling the device is safe.
Note:
Please observe applicable security measures
when handling electronic components sensitive
to electrostatic charges.
(DIN EN61340-5-1 /
DIN EN 61340-5-2).
2.1 Table mounting
Remove the protective strip from the rubber feet and fix them to
the marked locations.
2.2 Wall mounting
The unit can be mounted alternatively via VESA 75 standard at a
suitable mounting surface.
2.3.Rail mounting
Install the supplied rail mounting holder in the following
order:
WasherRail mounting holderDisk washerPan Head
screw to the device.
The unit is set at an angle from the top of the rail (1) and is
fixed by gently pushing it to the bottom (2). The unit must
engage significantly in the rail.
To release the unit from the DIN rail, proceed in reverse
order.
Note:
When installing the rail mounting holder, there is
danger of injury from sharp edges.
Note:
Be carfeful not to damage the rail mounting
holder while removing it.
3.1. Power supply connection
The power for this device can be supplied by a 24V DC
(7…36V) (3 pin plug). The corresponding connector is
included in the scope of delivery. Connect the device with
a suitable power supply unit.
Once the power supply is connected to the device, the
PWR LED is solid green.
(Front view)
4.1. UMTS Functionality at IRF2210
This variant (IRF2210) offers UMTS-Functionality. A
UMTS-Antenna is supplied (1) and a 3G Card Reader
(2) is available.
5.1.RJ45 network cable connection
For initial commissioning it is essential to establish a
connection between this device and a PC. Connect the
LAN port of the device with a PC.
Note:
The device with default settings operates as
DHCP client on the WAN interface. You can
use the WAN interface to configure the device
if you have a DHCP server which does not
serve IPs from the 192.168.0.0 range.
PIN-
NUMBER
SIGNAL
NAME
1 24V DC
2 GND
3 PE
5.2. Configuration of the PC-LAN-Network adapter
Open the Properties tab of the used network adapter.
Use following IP address
Access to the device is only enabled once the following
parameters have been entered:
IP address: 192.168.0. 100
Subnet mask: 255.255.255.0
(The last section of digits must represent a number
between 1 and 253; the value “
100 ” has been selected in
the example)
5.3. Access the webinterface
Start your web browser in order to open the web interface
of this device. Now enter the following IP address into the
address line of your browser:
http://192.168.0.254
5.4. Login
In the Login prompt window, the default settings must be
entered. The default settings, as delivered to the
customer, are:
User name: admin
Password: admin
Confirm your entry by using OK. Now, the device web
interface will appear.
Note:
If you are using a Proxy, it has to be deactivated
if neccessary.
Note:
We would recommend to make use of our
website contents (www.ads-tec.de) in order to
ensure an optimised data quality and to be
quickly and comprehensively informed of any
technical modification.
2. Mounting
4. UMTS Functionality at IRF2210
5. Configuration