PrehKeyTec MCI TouchKey - Handbuch (Seite 5)

PrehKeyTec GmbH MCI_TouchKey_Manual_V15.doc - 2011-02-09 Page 5/10
3 Modules
3.1 Magnetic stripe reader (MSR)
All magnetic cards according to ISO 7810 and 7811 can be read. The magnetic stripe reader records the entire information content of the
magnetic card. A LED signal (green Accept LED) is issued after a successful read procedure.
The magnetic card can be swiped through the reading device in both directions ( Figure 7 ). This provides easy manipulation for both right-
and left-handers
The parameters of the MSR can be set and/or modified using the corresponding PrehKeyTec
programming software.
You can find further information, as well as the associated software, on the Internet under
H
http://www.prehkeytec.com
H
.
Important notice: Please hold the magnetic card near the upper edge during a swipe.
3.2 Keylock (KL)
The optional keylock ( Figure 8 ) module has 5 positions and is supplied with 3 different keys.
All keys can be inserted and removed in both positions 0 and 1
The following switch positions can be set with the three keys:
• SUP key: 0 1 2 3 4
• REG key: 0 1
• X key: 0 1 2
By default, the code for the new switch position is transferred to the computer when the key is turned.
The parameters of the keylock can be set and/or modified using the corresponding PrehKeyTec
programming software.
You can find further information, as well as the associated software, in the Internet under
http://www.prehkeytec.com .
4 Software
4.1 TouchKey Programmer
TouchKey Programmer software is used for programming the TouchKey Module. The TouchKey Programmer helps you to:
•
Configure the TouchKey
• Create
layouts
• Test layouts on the TouchKey
•
Create XML files for communicating with the TouchKey
• Administering multiple TouchKey devices
4.2 TouchKey Demo Software
There is a TouchKey Demo package on our website
H
http://support.prehkeytec.com
H
which demonstrates the functionality of the MCI
TouchKey device. This example consists of a multiple of layouts with buttons, graphics and text. Furthermore it shows how to switch to other
layouts using buttons or keyboard keys on the device.
In order for this Demo Software to function, the appropriate key table for the keyboard section
needs to be downloaded into the device. This can be done using either the WinProgrammer or the
C2K. Further information can be found on the Readme file of the Demo package.
5 Additional Help
The most recent version of the TouchKey Programmer and further information can be found on our website
H
http://support.prehkeytec.com
H
You can reach our technical support department under:
Email: [email protected]
Fax: +49 9776 / 7046-299
Fig. 7 Magnetic stripe reader
Swipe direction
Turning direction
Fig. 8 Keylock
PrehKeyTec GmbH MCI_TouchKey_Manual_V15.doc - 2011-02-09 Page 5/10
3 Modules
3.1 Magnetic stripe reader (MSR)
All magnetic cards according to ISO 7810 and 7811 can be read. The magnetic stripe reader records the entire information content of the
magnetic card. A LED signal (green Accept LED) is issued after a successful read procedure.
The magnetic card can be swiped through the reading device in both directions ( Figure 7 ). This provides easy manipulation for both right-
and left-handers
The parameters of the MSR can be set and/or modified using the corresponding PrehKeyTec
programming software.
You can find further information, as well as the associated software, on the Internet under
H
http://www.prehkeytec.com
H
.
Important notice: Please hold the magnetic card near the upper edge during a swipe.
3.2 Keylock (KL)
The optional keylock ( Figure 8 ) module has 5 positions and is supplied with 3 different keys.
All keys can be inserted and removed in both positions 0 and 1
The following switch positions can be set with the three keys:
• SUP key: 0 1 2 3 4
• REG key: 0 1
• X key: 0 1 2
By default, the code for the new switch position is transferred to the computer when the key is turned.
The parameters of the keylock can be set and/or modified using the corresponding PrehKeyTec
programming software.
You can find further information, as well as the associated software, in the Internet under
http://www.prehkeytec.com .
4 Software
4.1 TouchKey Programmer
TouchKey Programmer software is used for programming the TouchKey Module. The TouchKey Programmer helps you to:
•
Configure the TouchKey
• Create
layouts
• Test layouts on the TouchKey
•
Create XML files for communicating with the TouchKey
• Administering multiple TouchKey devices
4.2 TouchKey Demo Software
There is a TouchKey Demo package on our website
H
http://support.prehkeytec.com
H
which demonstrates the functionality of the MCI
TouchKey device. This example consists of a multiple of layouts with buttons, graphics and text. Furthermore it shows how to switch to other
layouts using buttons or keyboard keys on the device.
In order for this Demo Software to function, the appropriate key table for the keyboard section
needs to be downloaded into the device. This can be done using either the WinProgrammer or the
C2K. Further information can be found on the Readme file of the Demo package.
5 Additional Help
The most recent version of the TouchKey Programmer and further information can be found on our website
H
http://support.prehkeytec.com
H
You can reach our technical support department under:
Email: [email protected]
Fax: +49 9776 / 7046-299
Fig. 7 Magnetic stripe reader
Swipe direction
Turning direction
Fig. 8 Keylock
PrehKeyTec GmbH MCI_TouchKey_Manual_V15.doc - 2011-02-09 Page 5/10
3 Modules
3.1 Magnetic stripe reader (MSR)
All magnetic cards according to ISO 7810 and 7811 can be read. The magnetic stripe reader records the entire information content of the
magnetic card. A LED signal (green Accept LED) is issued after a successful read procedure.
The magnetic card can be swiped through the reading device in both directions ( Figure 7 ). This provides easy manipulation for both right-
and left-handers
The parameters of the MSR can be set and/or modified using the corresponding PrehKeyTec
programming software.
You can find further information, as well as the associated software, on the Internet under
H
http://www.prehkeytec.com
H
.
Important notice: Please hold the magnetic card near the upper edge during a swipe.
3.2 Keylock (KL)
The optional keylock ( Figure 8 ) module has 5 positions and is supplied with 3 different keys.
All keys can be inserted and removed in both positions 0 and 1
The following switch positions can be set with the three keys:
• SUP key: 0 1 2 3 4
• REG key: 0 1
• X key: 0 1 2
By default, the code for the new switch position is transferred to the computer when the key is turned.
The parameters of the keylock can be set and/or modified using the corresponding PrehKeyTec
programming software.
You can find further information, as well as the associated software, in the Internet under
http://www.prehkeytec.com .
4 Software
4.1 TouchKey Programmer
TouchKey Programmer software is used for programming the TouchKey Module. The TouchKey Programmer helps you to:
•
Configure the TouchKey
• Create
layouts
• Test layouts on the TouchKey
•
Create XML files for communicating with the TouchKey
• Administering multiple TouchKey devices
4.2 TouchKey Demo Software
There is a TouchKey Demo package on our website
H
http://support.prehkeytec.com
H
which demonstrates the functionality of the MCI
TouchKey device. This example consists of a multiple of layouts with buttons, graphics and text. Furthermore it shows how to switch to other
layouts using buttons or keyboard keys on the device.
In order for this Demo Software to function, the appropriate key table for the keyboard section
needs to be downloaded into the device. This can be done using either the WinProgrammer or the
C2K. Further information can be found on the Readme file of the Demo package.
5 Additional Help
The most recent version of the TouchKey Programmer and further information can be found on our website
H
http://support.prehkeytec.com
H
You can reach our technical support department under:
Email: [email protected]
Fax: +49 9776 / 7046-299
Fig. 7 Magnetic stripe reader
Swipe direction
Turning direction
Fig. 8 Keylock