WolfVision VZ-9 User Manual - Handbuch (Seite 13)

DVI PORT
Serial control input, RS 232
9-pin D-Sub connector
on unit; male
(front side)
5
9
2
7
3 4
8
1
6
USB-PORT
The USB 2.0 output of the VZ-9 can be used to capture and
transfer Visualizer images onto a computer in a fraction of a
second. No additional computer hardware (like a grabber card)
is required. In this way the Visualizer can be used as a 3-D
scanner for your computer. Just connect the USB port
(#19) of
the Visualizer and the USB port of your computer, using the
supplied USB cable. The software is fully twain compatible. The
USB 2.0 output is fully USB 1.1 compatible (less speed).
The WolfVision USB-software can be found on the supplied CD-ROM. Please check our
Internet homepage at:
www.wolfvision.com/support if an update of this software is available
as a free-download. The software works under Windows 98/ME/2000/XP. Windows 95 and NT
will not work, because they do not support USB.
Ethernet / LAN
The LAN connection (10BASE-T/100BASE-TX) can be used for controlling the VZ-9 over a
computer network. Image transfers, firmware updates and displaying status information is
possible. In addition units with serial numbers largen then 095501 can send out e-mail
notifications.
The following protocols are supported: TCP/IP, ICMP and ARP.
: Supportet Browsers are Internet Internet Explorer, Netscape Navigator and Mozilla.
By default, DHCP is activated to receive all settings automatically.
Image Transfer Resolution: Still Image: 1024x768 (or 512x384), Live Image: 160x120
Please check the separate ETHERNET / LAN description on our internet homepage at:
www.wolfvision.com/support
(or on the supplied CD-Rom).
The complete serial protocol can be found on our internet homepage: www.wolfvision.com /support
The serial port can be used to control the Visualizer through an external device, like a remote
control system for a complete conference room.
Pins: 2: RX, 3: TX, 5: GND, 7: RTS, 8: CTS
Baud rate: 9200, 19200, 38400, 57600 or 115200 (selectable)
databits: 8, stopbit: 1, parity: no
Please note that DecimaI-Codes (=ASCII-Codes or Hex-Codes)
must be sent as one single byte (e.g. 199 and not: 1 + 1 + 9) !
1. Remove the power cord of the Visualizer.
2. Remove the safety screw by using the supplied Allen key. (if available)
3. Remove the lamp cover itself by turning the case.
4. Change the lamp (lift the safety ring before). Place the new lamp very carefully into the socket.
CAUTION: LAMP CAN BE HOT!
5. Mount the lamp cover in reverse order (3. to 1.) and set the safety screw.
Lamp type: 4642 halogen lamp 12V/35W incl. heat shield and mounting ring.
4000 h average burning life
Changing the lamp of the Visualizer
12
Pin 24
Pin 8
Pin 1
Pin 9
Pin 17 C4
C1 C2
C3
C5
1 - T.M.D.S. Data2- 9 - T.M.D.S. Data1- 17 - T.M.D.S. Data0-
2 - T.M.D.S. Data2+ 10 - T.M.D.S. Data1+ 18 - T.M.D.S. Data0+
3 - T.M.D.S. Data2/4 Shield 11 - T.M.D.S. Data1/3 Shield 18 - T.M.D.S. Data0+
4 - T.M.D.S. Data4- (*) 12 - T.M.D.S. Data3- (*) 19 - T.M.D.S. Data0/5 Shield
5 - T.M.D.S. Data4+(*) 13 - T.M.D.S. Data3+ (*) 20 - T.M.D.S. Data5- (*)
6 - DDC Clock 14 - +5V Power 21 - T.M.D.S. Data5+ (*)
7 - DDC Data 15 - Ground (return for +5V, 22 - T.M.D.S. Clock+
8 - Analog Vertical Sync (**) HSync and Vsync) 23 - T.M.D.S. Clock-
C1 - Analog Red (**) 16 - Hot Plug Detect 24 - Analog Vertical Sync (**)
C4 - Analog Horizontal Sync (**) C2 - Analog Green (**) C3 - Analog Blue (**)
C5 - Analog Ground (**) *...not used
(analog R, G & B return) **...not available on units with serial number lower than 095500