WolfVision VZ-27 User Manual - Handbuch (Seite 14)

DVI PORT
SERIAL PORT / SERIAL PROTOCOL
Pins: 2:RX, 3:TX, 5:GND
9-pin D-Sub connector
on unit, male, front side
A detailed description of the serial protocol (including status
report and position setting) is available on request from your
WolfVision dealer or can be downloaded from our website:
http://www.wolfvision.com/support.
Pin 1
Pin 24
Pin 8
Pin 9
Pin 17
1 - T.M.D.S. Data2-
2 - T.M.D.S. Data2+
3 - T.M.D.S. Data2/4 Shield
4 - T.M.D.S. Data4- (not used)
5 - T.M.D.S. Data4+(not used)
6 - DDC Clock
7 - DDC Data
8 - Analog Vertical Sync
C1 - Analog Red
C4 - Analog Horizontal Sync 9 - T.M.D.S. Data1-
10 - T.M.D.S. Data1+
11 - T.M.D.S. Data1/3 Shield
12 - T.M.D.S. Data3- (not used)
13 - T.M.D.S. Data3+ (not used)
14 - +5V Power
15 - Ground (return for +5V,
HSync and VSync)
16 - Hot Plug Detect
C2 - Analog Green
C5 - Analog Ground
(analog R, G & B return) 17 - T.M.D.S. Data0-
18 - T.M.D.S. Data0+
19 - T.M.D.S. Data0/5 Shield
20 - T.M.D.S. Data5- (not used)
21 - T.M.D.S. Data5+ (not used)
22 - T.M.D.S. Clock+
23 - T.M.D.S. Clock-
24 - Analog Vertical Sync
C3 - Analog Blue
For standard use of the WolfVision Visualizer it is NOT necessary to go into the Visualizer's menu and change
settings. Inexperienced users should not try to make any adjustments there. That is why the keys for the
Visualizer menu (#26 and #27) are dark on the control panel and not easy accessible.
These keys and the on-screen menu only become visible after pressing the MENU key (#23) for 1 second !
This is to prevent that the menu key is pushed by accident by an inexperienced user.
ON-SCREEN MENU / CAMERA MENU
The following chapters are for experienced users only:
When the menu appears on the screen, settings of the Visualizer's basic functions and the
built-in camera can be made using the 4 select keys (#26).
If you require more information on a function in the on-screen menu just set the cursor in
the respective line and press the HELP key (#25). A detailed description of this function
appears on the screen.
The functions of the on-screen menu are not described in this user manual as the help menu is an integrated
part of the Visualizer's software. The information you see on your screen always belongs to the current Visualizer
software (firmware).
RESET OF ON-SCREEN MENU SETTINGS / PRESETS
The settings in the on-screen menu can be set back to the factory defaults. "Reset" is one item in the on-screen
menu. In case you can not read the menu on a screen you can also set the unit back to the factory defaults by
simultaneously pressing the keys: RESET (#20) + MENU (#23).
The on-screen menu also offers the possibility to store three different menu settings as Menu-presets.
DVI ports are divided into a digital and an
analog section. Please note that the image
of the External input (#42) is only output
at the analog DVI section!
SWITCHING TO NEGATIVE, NEGATIVE/BLUE and BLACK/WHITE
The output image of the Visualizers can be switched from positive to negative in the on-screen menu. In addition the
background of a negative image can be switched to blue for better readability of text. You can also switch between
color and black and white in the on-screen menu.
TIP: If you switch often to negative, negative/blue or black/white images you can assign this function to one of the
Preset keys (#14) in the on-screen menu.
5
9
2
7
3 4
8
1
6
14
FIRMWARE UPGRADES
The software (firmware) of your Visualizer (including the o ) can easily be upgraded to the latest
version. First download the latest firmware and WolfVision's firmware update utility program from Wolfvision's
internet homepage at www.wolfvision.com/support. Then connect the serial port of the Visualizer with
the serial port of your computer using a crossed serial RS232 cable and run the firmware update utility program.
More details on the firmware updates can be found on WolfVision's internet homepage.
n-screen HELP