Bullard RXE - Handbuch (Seite 6)

www.bullard.com
Cleaning and Storage
Always keep your safety helmet clean. If necessary, clean it before you examine it. Do
not use the helmet if it is still wet after use or cleaning.
Manual cleaning
Do not use abrasive cleaners, benzine or solvents such as acetone, alcohol or similar to
clean fire service helmets.
The universal cleaning agent Secusept™ Cleaner (0.5-1.0% solvent) and the disinfectant
Incidur as well as mild soapy water are approved.
• Wipe helmet shell and all plastic parts of the interior lining with a damp cloth, then rub
dry.
• Clean the visor with lukewarm soapy water or alcohol-free glass cleaner, then rinse
and wipe dry.
• Remove straps and fabric of the interior lining then wash and disinfect together with
the duty clothing in the wash bag.
Machine cleaning
WARNING
The fire service helmet is subject to very strong mechanical loads during machine
cleaning. It can be damaged if the following information is not observed.
The helmet can be washed as follows in the washing machine.
• Pack helmet in a padded wash bag (for wash bag see Bullard helmet accessories)
• Load washing machine so that only one further helmet would fit into the drum
• Preselect “swivel program” for respirators
• Start wash
• Rinse four times
• Dry helmet thoroughly
Cleaning agents:
Approved cleaning agents: Eltra heavy-duty washing power with disinfecting properties,
manufacturer: Ecolab
Dosage: 5g Eltra per 1 L fresh water
Water temperature: 62°C ± 2°C
Storage:
Store and transport your safety helmet so that it is protected against moisture,
preferably in the original packaging.
Life and Maintenance of your
Bullard Fire Helmet
Your helmet is designed to help absorb energy and impact. In addition, the helmet offers
protection against flames, sparks, high temperature and liquid chemicals.
The helmet can be damaged or even destroyed as it protects against these hazards.
After a hard impact you should replace your helmet IMMEDIATELY, even if there is no
visible damage on the outside of the helmet.
It should also be replaced if the helmet has been exposed to extreme heat such as a
flash-over.
You should NEVER use a damaged helmet.
It must be repaired – if possible – or be rendered unserviceable.
The length of your helmet’s service life is determined by the materials used in its
construction as well as the environment in which the helmet is used and stored.
This firefighting helmet with its painted helmet shell of high-strength and temperature-
resistant composite exhibits excellent aging resistance and if undamaged it does not
undergo any changes by sunlight (UV radiation).
The life of the helmet is primarily limited by the effects of mechanical, thermal and
chemical stresses.
The composite used in your helmet is considered very resistant to these stresses.
Furthermore, the helmet’s life is influenced by the amount and diligence of care and
maintenance.
The management of your fire department is responsible for deciding on the time for
removing the helmet from service.
Contact your local sales distributor or Bullard Europe directly if in doubt or to check your
helmet.
At regular intervals, conduct a check of the helmet shell, inner parts, straps and
accessories.
Retirement Criteria’s
Outer shell
Even a slight collision or impact may compromise the structural integrity of the material
without any direct visual evidence of damage. This also applies to thermal stresses. A
thumb pressure check can be performed to check for existing damage:
If the helmet shell can be deformed by a thumb press at the affected site, the strength of
the helmet shell structure has been compromised.
The helmet must be replaced and rendered unserviceable.
Replace the following components, if one or more of the conditions listed below applies:
Outer shell
- cracks, dents or scratches with a depth greater than 1mm
- any type of deformation
Inner shell (inner liner)
- changes in surface appearance, especially melted material
Visor
- blistering, cracks, melted material spots
- significant scratches
- deformation
- visor cannot be mounted securely in desired position; replace visor mount if necessary
Protective edging (if this feature is included)
- cracks, fraying, melted material; if applicable, glue loose protective edging back in place
Reflective stripes
- missing, burned or no longer reflective
Chin strap and head bands
- worn, missing or broken parts
- damaged seams
- worn hook-and-loop (Velcro) joints
- worn, broken or missing clip closure
- tears and wear
- brittleness
- discoloration
Head ring
- material embrittlement
- cracked or broken
- twist-lock is faulty
Cover fabrics, neck protection
- loose, cracked or frayed seams
- fire damage, discoloration
- cracks or perforation
Screws
- missing
- check for tight seating of all screws
Bullard recommends an annual inspection of your helmet by a trained specialist.
After several years, destructive tests may be performed on a random sampling basis to
check the protective properties of an inventory of helmets.
Contact your local sales distributor or Bullard Europe regarding such testing.
6
Service Life and Mainenance/A
ssembly and Disassembly