WolfVision EYE-12 User Manual - Handbuch (Seite 12)

11
+ 12V
GND
When a locked power connector and/or other power supply is necessary, the
supplied power connector can be used.
The power supply is optional if Power over Ethernet (PoE) is used (see page 12).
The power source equipment shall comply with all applicable local and
national codes related to safety.
Power Plug
DVI-I Port
1 - T.M.D.S. Data2- 9 - T.M.D.S. Data1- 17 - T.M.D.S. Data0-
2 - T.M.D.S. Data2+ 10 - T.M.D.S. Data1+ 18 - T.M.D.S. Data0+
3 - T.M.D.S. Data2/4 Shield 11 - T.M.D.S. Data1/3 Shield 18 - T.M.D.S. Data0+
4 - T.M.D.S. Data4- (*) 12 - T.M.D.S. Data3- (*) 19 - T.M.D.S. Data0/5 Shield
5 - T.M.D.S. Data4+(*) 13 - T.M.D.S. Data3+ (*) 20 - T.M.D.S. Data5- (*)
6 - DDC Clock 14 - +5V Power 21 - T.M.D.S. Data5+ (*)
7 - DDC Data 15 - Ground (return for +5V, 22 - T.M.D.S. Clock+
8 - Analog Vertical Sync HSync and Vsync) 23 - T.M.D.S. Clock-
C1 - Analog Red 16 - Hot Plug Detect 24 - Analog Vertical Sync
C4 - Analog Horizontal Sync C2 - Analog Green C3 - Analog Blue
C5 - Analog Ground *...not used
(analog R, G & B return)
m
Pin 24
Pin 8
Pin 1
Pin 9
Pin 17 C4
C1 C2
C3
C5
The DVI-I port (#13) provides digital and analog signals.
For using HDMI, a DVI-HDMI cable or adapter is required.
In some rooms, the built-in IR-receiver may . In this case connect the supplied external
receiver to the IR-SENSOR plug (#12) and position the IR-sensor somewhere on the ceiling (or in
the room)
not be enough
infrared
where the users normally point the remote control at.
External Infrared (IR) Sensor
RS-232, Serial Control Input
9-pin D-Sub connector
on unit; male
(front side)
5
9
2
7
3 4
8
1
6
The serial port (#10) can be used to control the EYE-12 through an external device, such as a room control
system.
Pins: 2: RX, 3: TX, 5: GND
Baud Rate: 9200, 19200, 38400, 57600 or 115200 (selectable)
databits: 8, stopbit: 1, parity: no
The baud rate can be changed in the on-screen extra menu by keeping
pressed the menu key until it appears (see page 10).
RGB Port
1 - Analog Red video 6 - Red return 11 - N/C Not connected
2 - Analog Green video 7 - Green return 12 - SDA I²C data
3 - Analog Blue video 8 - Blue return 13 - HSync Horizontal sync
4 - N/C Not connected 9 - SENSE +5 V DC from Visualizer 14 - VSync Vertical sync
5 - GND Ground 10 - GND Ground (VSync, DDC) 15 - SCL I²C clock
1
11
5
15
15-pin D-Sub HD
connector female
(front side, unit)
The RGB port (#11) provides analog RGBHV signal.
IMPORTANT
DVI-I connector female
(front side, unit)
The complete protocol can be found on our internet website under: www.wolfvision.com/support