intimus 529 - Handbuch (Seite 7)

The machine may not be modified in
any way!
Operation of the machine is prohibited
if modifications are undertaken.
FAULT CHECKLIST:
If the machine does not work, check the following
points:
- is the mains plug connected to the mains?
- is the main switch (1) switched on?
- is the door closed?
- is the bin pushed in?
- is the bin full?
The bin must be emptied.
- has the cutter been overloaded?
Follow the instructions under “OVERLOAD OF
THE CUTTING UNIT”
- has the motor been overloaded?
See description under “MOTOR FAULT”
- has a phase failed?
Check the three phase fuses on the mains
socket and replace if necessary.
If you still cannot isolate the fault or
other faults are statable, the machine
shouldn’t be operated. Please report
to / notify our customer service de-
partment.
Always unplug the machine from the
mains power supply, turn off the main
switch and lock it with a padlock before
opening the machine to carry out any
repairs.
OVERLOAD OF THE CUTTING UNIT
(Auto-Reverse function)
If the cutter is overloaded, for example due to
feeding in unsuitable materials, the machine
reacts as follows:
- The cutter is blocked, then runs backwards
briefly (material is released) and stops. The
motor is switched off. The pilot lamp II (6)
flashes.
Proceed as follows:
- Remove the remaining material from the feed
shaft (7).
- Briefly press either the pushbutton “Cutter
forwards” (2) or “Stop cutter” (3) once. The
pilot lamp II (6) (Fig. 2) goes out.
- Press the pushbutton “Cutter forwards” (2) (Fig.
2) again. After a certain time delay, the cutter
runs forwards and processes the remaining
material in the cutter.
- Compacting via the feed shaft can be
continued.
Note: If the cutter is blocked again by non-
compactable material in the cutter, the machine
must be opened and the material removed from
the cutter slot by hand.
Switch the machine off at the main switch (1)
(Fig. 2), disconnect the mains plug and inform a
person who is authorised to carry out this work.
MOTOR FAULT:
The machine is equipped with a thermally protec-
ted motor. Should this motor be overloaded, it will
switch off automatically. In such case the pilot lamp
II „MOTOR FAULT“ (6) (fig. 2) comes on.
After a cooling down period of approx. 10 minutes
(depending on the room temperature) you can
restart the machine and continue shredding.
MAINTENANCE GEAR / LIGHT BARRIER:
Once a month the two synchronous wheels as
well as the chain wheels and the drive chain
must be regreased.
The machine must be turned off at the
main switch (1) (fig. 2) and unplugged
before the machine is opened.
Proceed as follows:
1. Remove both side covers of the housing.
2. Grease the above-mentioned parts of the gear
with a brush or a grease gun with conventional
lubricating grease.
3. Reinstall the side covers and plug the mains
plug in. The machine can be put back into
operation.
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine
or its packaging with household trash.
7
MALFUNCTION
MAINTENANCE TECHNICAL DATA
Inlet opening: 415x200 mm
Compacting capacity:
Plastic bottles 0.5 l:
approx. 8,200 / hr
Drink cans 0.33 l: approx. 21,600 / hr
Working width: 410 mm
Power: 3,9 kW
Supply voltage: 400V/50Hz
415V/50Hz
Pre-fusing:
(gl fuse, type 1 assignment)
400V-415V/50Hz:
16 A
Width: 810 mm
Depht: 1380 mm
Height: 1950 mm
Noise level: ca. 70 dB(A)
Weight: ca. 290 kg
DISPOSING
GB Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
529
91574 2 10/1
1