Denon DN-S3000 - Handbuch (Seite 20)

A
B
B
∗
20
ENGLISH
GENERAL
Type: Compact disc player
Disc type: Standard compact discs (12 cm discs), CD-TEXT
CD-R, CD-RW discs
NOTE: Finalized CD-R or CD-RW discs can be played back in this unit.
However, according to recording quality, some CD-R/RW discs
cannot be played.
Dimensions: Player unit: 285 (W) x 111.5 (H) x 327 (D) mm (without feet)
11-7/32” (W) x 4-25/64” (H) x 12-7/8” (D)
Installation: Table top type
Mass: Player unit: 6.0 kg (12 lbs 9 oz)
Power supply: U.S.A., Canada and Taiwan R.O.C. models: 120 V AC ±10%, 60 Hz
European models:
230 V AC ±10%, 50 Hz
Power consumption: 16 W
Environmental conditions: Operational temperature: 5 to 35°C (41 to 95°F)
Operational humidity: 25 to 85% (no condensation)
Storage temperature: –20 to 60°C (4 to 140°F)
AUDIO SECTION
Main out, Monitor out
Quantization:
24-bit linear per channel
Sampling frequency: 44.1 kHz at normal pitch
Oversampling rate: 8 times
Total harmonic distortion: 0.01% or less
Signal to noise ratio: 90 dB or more
Channel separation: 85 dB or more
Frequency response: 20 to 20,000 Hz
Analog output
Output level: 2.0 V r.m.s.
Load impedance: 10 k Ω/kohms or more
Digital output
Signal format: IEC958-Type II
Output level: 0.5 Vp-p 75 Ω/ohms
FUNCTIONS
Instant start: Within 20 msec.
Variable pitch: ±4% (0.02% pitch), ±10% (0.1% pitch), ±16% (0.1% pitch)
±24% (0.1% pitch), ±50% (0.5% pitch) ±100% (1.0% pitch)
Pitch bend: Pitch range ±32%
Pitch range ±100%:
±99%
Sampler
Sampling: 44.1 kHz
Length: 15 sec.
Output level: 2.0 V r.m.s. (Variable / -14 ~ +6 dB)
Variable pitch: ±24% (0.1% pitch)
Search precision: 1/75 sec. (1 subcode frame)
Max. scan speed: Over 20 times normal speed
Max. MEMO memory steps: 5000 steps
✽ Specifications and design are subject to change without notice for purpose of improvement.
15 SPECIFICATIONS
1. Remove a screw (Hexagon socket head) and
pull out Scratch Disc and Slip Mat.
2. Remove Belt from Motor Pully.
3. Remove 3 screws (< head) and pull out
Platter.
4. Remove Belt from Platter.
5. Mount in the order 4 → 1.
B
A
Platter
Stabilizer
(Hexagon socket head)
Scratch Disc
Slip Mat
Belt
Motor Pully
(< head)
CAUTIONS:
• Unplug the power cord before replacing the
belt.
• Do not touch the sensor or scale( ∗) when
removing the Platter.
• Do not apply oil or grease to the belt when
replacing it.
Belt
Platter
(< head)
16 REPLACING THE BELT
• On the DN-S3000, the platter is driven by a belt. In the unlikely case of trouble, use the procedure described
below to replace the belt.
Slip Sheet