Denon DN-S3000 - Handbuch (Seite 7)

( head)
A
+ Adaptor
Stabilizer
7" (17 cm) record
7" (17 cm)
record adaptor
B (Hexagon socket head)
Washer
Shaft
Scratch Disc
Stabilizer
Slip mat
Slip sheet
(White)
Anti-static
sheet
(Black)
B (Hexagon socket head)
Washer
Slip mat
Slip sheet (White)
7
ENGLISH
2 CONNECTIONS/INSTALLATION/
INSTALLING THE 7“(17cm) RECORD ADAPTOR
(1)CONNECTIONS
1. Turn off the POWER switch.
2. Connect the RCA pin cords between the DN-S3000 outputs and inputs of your mixer.
3. If your mixer has Fader Start function such as our DENON DN-X800 or DN-X400, connect FADER 1, 2 jacks to
the mixer using 3.5 mm stereo mini cord.
4. If you have a DENON DN-X800 mixer, you can use the X-Effect function to control the Hot Starts, Samplers
and Brake from the crossfader to get wide variety of operation.
CH1 CH2 CH3 CH4
FADE
Rch1
FADE
Rch2
DN-X400
LINE OUT FADER
DN-S3000
X'EFFECT
IN
X'EFFECT
OUT
3.5 mm stereo mini cord
RCA cord
Fig. 1 : Fader start connections example 1 Fig. 2 : X-Effect connections example 1
CH1 CH2 CH3 CH4
FADE
Rch3
FADE
Rch4 X'EFFECT
DN-X800
LINE OUT FADER
DN-S3000
CD1
X'EFFECT
IN
X'EFFECT
OUT
LINE OUT FADER
DN-S3000 or DN-S5000
CD2
X'EFFECT
IN
X'EFFECT
OUT
• X-EFFECT playback is possible with the CD 1 and
CD 2.
• The memos of player and player can be compared
when the CD players are connected by X-EFFECT.
• Relay play
(2)INSTALLATION
The DN-S3000 will work normally when the unit is installed with in 20 degrees off the level surface.
If the unit is titled excessively, the disc may not be loaded properly.
NOTE:
Standing up of playback slows unusually after trans porting the product.At the time, push center of the
!1 Scratch Disc lightly.
MAX 20 °
Front
1. Remove a screw (Hexagon socket head)
and pull out Stabilizer, Scratch disc, Slip mat,
Slip sheet (White) and Anti-static sheet
(Black).
2. Set Adaptor in the hole of 7” record.
3. Install Stabilizer in Adaptor.
4. Fix Adaptor with 3 screws.
(<head).
5. Install Slip sheet (White), Slip mat and 7”
(17cm) record adaptor in Shaft of the product.
(Do not install Anti-static sheet (Black).)
Attention
Fit the D shape of Shaft to the D hole of
Stabilizer.
6. Install a screw (Hexagon socket head)
through Washer.
B
A
B
(3)INSTALLING THE 7” (17cm) RECORD ADAPTOR
Your own 7” (17cm) vinyl record can be installed on this product by using the provided adaptor.
This original design grants you the freedom to use your favorite vinyl record for that ultimate analog turntable feel.
*Make sure the record used is flat and not warped.
• 7” (17cm) record adaptor accessories
q Adaptor......................................1
w Screw(<head) ..........................3
e Washer(Reserve) ......................1
NOTE:
• When RECORD to be used and friction of Slip
mat are small, it may be unable to playback
normally.