JUMO 14597 safetyM TB/TW08 Temperature Limiter and Temperature Monitor Operating Manual Benutzerhandbuch
JUMO Ausstattung
Advertising
Inhaltsverzeichnis
Document Outline
- Bedienübersicht
- 1 Kurzbeschreibung
- 2 Geräteausführung identifizieren
- 3 Montage
- 4 Elektrischer Anschluss
- 5 Gerät in Betrieb nehmen
- 6 Parameterebene
- 7 Konfigurationsebene
- 7.1 C111 Analogeingänge
- 7.2 C112 Einstellung für Doppelthermoelement
- 7.3 C113 Einheit, Nachkommastelle
- 7.4 C114 Gerätefunktion
- 7.5 C115 Schaltverhalten
- 7.6 C116 Anzeige nach dem Einschalten
- 7.7 C117 Funktion Binäreingang
- 7.8 C118 Anzeigenabschaltung nach Timeout
- 7.9 C119 Funktion Voralarm
- 7.10 SCL, SCH, ALLO, ALHI, OFFS, HYS1, HYS2
- 7.11 C 120 Grenzwert für Relais-Schaltspiele
- 7.12 C 121 Zählerstand für Relais-Schaltspiele
- 7.13 C 122 Betriebsstundenzähler
- 7.14 oInP, oSiG, oSCL, oSCH, oErr für Analogausgang
- 7.15 Verhalten beim Verlassen des Skalierungsbereichs
- 8 Technische Daten
- 9 Fühler für Luft
- 11 Fühler für Luft, Wasser und Öl
- 12 Zertifikat
- 13 Setup-Programm
- 14 Alarmmeldungen
- 15 Fehlermeldungen
- 16 Was ist wenn...
- B70.1170.0en.pdf
- Operating overview
- 1 Brief description
- 2 Identifying the device version
- 3 Installation
- 4 Electrical connection
- 5 Commissioning/starting up the device
- 6 Parameter level
- 7 Configuration level
- 7.1 C111 Analog inputs
- 7.2 C112 Setting for double thermocouple
- 7.3 C113 Unit, decimal places
- 7.4 C114 Device function
- 7.5 C115 Switching behavior
- 7.6 C116 Display after switch-on
- 7.7 C117 Binary input function
- 7.8 C118 Display shut-down after timeout
- 7.9 C119 Pre-alarm function
- 7.10 SCL, SCH, ALLO, ALHI, OFFS, HYS1, HYS2
- 7.11 C 120 Limit value for relay alternations
- 7.12 C 121 Counter reading for relay alternations
- 7.13 C 122 Operating hour counter
- 7.14 oInP, oSiG, oSCL, oSCH, oErr for analog output
- 7.15 Behavior when the scaling range is exceeded
- 8 Technical Data
- 9 Probes for air
- 11 Probes for water, oil and air
- 12 Certificates
- 13 Setup program
- 13.1 Minimum hardware and software prerequisites:
- 13.2 Displaying the device software version
- 13.3 Activation of the access code
- 13.4 Restricting the setting range for the limit value AL (minimum and max. value master)
- 13.5 2x Pt100 for differential value calculation with prefix
- 13.6 2x Pt100 for differential value calculation as absolute value
- 14 Alarm messages
- 15 Error messages
- 16 What to do, if ...