Banner EZ-ARRAY USB Serial Adapter Benutzerhandbuch

Handbuch für a-gage, Ez-array, Technische merkmale

Advertising
background image

ACHTUNG . . .

Darf nicht für den Personenschutz verwendet werden

Verwenden Sie diese Produkte niemals als Messwertgeber für den Personenschutz. Dies könnte zu schweren oder tödlichen Verletzungen führen.

Die in dieser Broschüre beschriebenen Produkte verfügen NICHT über die selbstüberwachenden redundanten Schaltungen, die für Personenschutz-Anwendungen erfor-
derlich sind. Ein Sensorausfall oder Defekt kann zu unvorhersehbarem Schaltverhalten des Ausgangs führen. Sicherheitsgeräte, welche die Anforderungen der Normen
OSHA, ANSI und IEC für den Personenschutz erfüllen, finden Sie im aktuellen Banner-Sicherheitsprodukte-Katalog.

11/08

Ident-Nr. 140060 Rev. A

Handbuch für A-GAGE

®

EZ-ARRAY

™

Zweiteiliger messender Lichtvorhang mit 2 Analog- und 2 Schaltausgängen sowie seriellem Ausgang

Technische Merkmale

Schnell und einfach zu montierender, kostengünstiger, zweiteili-

•

ger Lichtvorhang für schwierigste Messanwendungen.
Hervorragend bei schnellen, präzisen Prozessüberwachungs- und

•

Prüfanwendungen, Profilerfassungen und

Bandführungsanwendungen
Umfangreiche Kombinationsmöglichkeiten von Scan-Funktionen:

•

14 Mess-Modi (“Scan-Analyse”)

–

3 Scan-Methoden

–

Einstellbare Strahlausblendung

–

Einstellbare kontinuierliche oder torgesteuerte Scan-Initiierung

–

Einstellbarer Schwellenwert für halbtransparente Anwendungen

–

2 Analogausgänge, 2 Schaltausgänge sowie serieller Ausgang

–

Modbus 485-RTU

Außergewöhnliche 4-m-Reichweite mit 5-mm-Strahlabstand

•

In 12 Längen von 150 mm bis 2400 mm erhältlich

•

Ausgezeichnetes 5-mm-Detektionsvermögen oder 2,5-mm-Kan-

•

tenauflösung, je nach Scan-Methode
Empfänger-Benutzeroberfläche für die schnelle Einrichtung vieler

•

Standardanwendungen:

6-Positions-DIP-Schalter zur Einstellung von Scan-Modus,

–

Mess-Modus, Analogausgangskurve und Schaltausgang 2

(antivalente Messung oder Alarm)

2 Drucktaster zur Einstellung von Funktionsreservemethode

–

und Ausrichtung/Ausblendung

7 Zonen-LEDs für sofortige Informationen zu Ausrichtung und

–

Strahlunterbrechung

Dreistelliges Display für Messinformationen und Diagnose

–

PC-Benutzer-Software für erweiterte Konfiguration erhältlich

•

Optionale externe Programmierleitung für Ausrichtung, Funktions-

•

reserveeinstellungen, invertiertes Display und DIP-

Schaltersperrung

Advertising
Dieses Handbuch ist für die folgenden Produkte bezogen werden:
Inhaltsverzeichnis

Document Outline

  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
  • 1. Overview
    • 1.1 System Components
    • 1.2 Features
    • 1.3 Configuration via DIP Switch or PC Interface
    • 1.4 Status Indicators
    • 1.5 Receiver Gray (Remote Teach) Wire
    • 1.6 Scanning Method
    • 1.7 Gain Configuration
    • 1.8 Electronic Alignment Routine
    • 1.9 Blanking
    • 1.10 Measurement Mode Selection
    • 1.11 Analog Output Configuration
    • 1.12 Discrete Output Configuration
    • 1.13 Serial Communication
  • 2. Components and Specifications
    • 2.1 Sensor Models
    • 2.2 Cordsets and Connections
    • 2.3 Alignment Aids
    • 2.4 Accessory Mounting Brackets and Stands
    • 2.5 Replacement Parts
    • 2.6 Specifications
    • 2.6 Specifications, continued
    • 2.7 Emitter and Receiver Dimensions
    • 2.8 Standard Bracket Dimensions
  • 3. Installation and Alignment
    • 3.1 Mounting the Emitter and Receiver
    • 3.2 Mechanical Alignment
    • 3.3 Hookups
    • 3.4 Optical Alignment
  • 4. Using the Receiver User Interface
    • 4.1 Configuration DIP Switch
    • 4.2 Alignment / Blanking Button (Electronic Alignment)
    • 4.3 Gain (Sensitivity Adjust) Button
    • 4.4 Inverting the 3-Digit Display
    • 4.5 Troubleshooting and Error Codes
  • 5. Using the PC Interface (Banner Sensors GUI)
    • 5.1 Supplied Software
    • 5.2 Communications Connections
    • 5.3 Accessing the GUI
    • 5.4  Factory Defaults
    • 5.5 Alignment and Blanking
    • 5.6 Configuration Setup
    • 5.7 System Config View
    • 5.8 Analog Output Config View
    • 5.9 Discrete Output Config View
    • 5.10 Comm Config View
    • 5.11 Part Number and Version Info View
    • 5.12 System Diagnostics View
    • 5.13 Communications Troubleshooting
  • Appendix A. Modbus Reference
  • Glossary
Zie ook andere documenten in de categorie Banner Sensoren: