Evo Fitness XGA Benutzerhandbuch

Seite 23

Advertising
background image

23

UTILIZZO DEL PROIETTORE

Una volta eseguita l'installazione, accendere
tutte le apparecchiature in uso.

Per accendere il proiettore, spingere con
decisione il pulsante POWER (ACCENSIONE)
sul tastierino o sul telecomando. Si illumina
l'indicatore STATUS (STATO) che quando viene
accesa l'unità passa da giallo a verde.

Se l'indicatore di STATO è giallo lampeggiante,
attendere che si stabilizzi sul giallo fisso.

Quando è collegata una sola sorgente, essa
viene rilevata automaticamente dal proiettore.
Se sono collegate più sorgenti, il proiettore
cerca quella attiva successiva, secondo
l'elenco che segue, a condizione che SOURCE
SCAN sia impostato su ON nel menu
secondario SET UP (vedere descrizione del
sistema di menu):

- VGA 1
- VGA 2
- DVI-D
- Component
- S-Video
- Composite Video

Selezionare le sorgenti premendo il pulsante
SOURCE (SORGENTE) sul tastierino o sul
telecomando. Verranno visualizzate solo le
sorgenti attive.

Se non è attiva alcuna sorgente, saranno
visualizzati sulla schermata dei messaggi di
ricerca.

Quando non si attiva alcuna sorgente per
molto tempo, il proiettore passa in modalità
standby se la funzione DPMS (risparmio
energetico) è impostata su ON nel menu
secondario SET UP (IMPOSTAZIONE). La spia
STATUS passa da verde a giallo lampeggiante
e poi a giallo. Il proiettore viene riacceso se
viene (ri)attivata almeno una sorgente. La
funzione di spegnimento può essere
disabilitata tramite menu. Vedere DPMS nel
menu secondario SET UP.

Per spegnere il proiettore, spingere con
decisione il pulsante POWER sul tastierino o
sul telecomando per due volte (per confermare
che si desidera effettivamente spegnere
l'unità). La spia STATUS passa da verde a giallo
lampeggiante e poi a giallo quando il proiettore
viene spento.

L'unità non può essere riaccesa se la spia
STATUS è giallo lampeggiante; attendere che la
spia si stabilizzi sul giallo fisso.

UTILIZACIÓN DEL PROYECTOR

Una vez instalado, apague todo el equipo.

Para encender el proyector, pulse con firmeza
el botón POWER del teclado o del mando a
distancia. El indicador de estado STATUS
pasará de amarillo a verde cuando se encienda
el aparato.

Si el indicador STATUS está amarillo
intermitente. Espere a que se quede en
amarillo fijo.

Cuando sólo hay conectada una fuente, el
proyector detectará automáticamente dicha
fuente. Si hay más fuentes conectadas, el
proyector buscará la siguiente fuente activa de
acuerdo con la siguiente lista, siempre que
SOURCE SCAN del submenú
CONFIGURACIÓN esté en ON (véase la
descripción del sistema de menús):

- VGA 1
- VGA 2
- DVI-D
- Component
- S-Video
- Composite Video

Seleccione las fuentes pulsando los botones
SOURCE del teclado o el mando a distancia.
Sólo se mostrarán las fuentes que estén
activas.

Si no hay ninguna fuente activa, en la pantalla
aparecerá que está buscando mensajes.

Si no hay ninguna fuente activa durante mucho
tiempo, el proyector entrará en modo de
espera si en el submenú CONFIGURACIÓN se
ha puesto DPMS (ahorro de energía) en ON. El
indicador STATUS pasará de verde a amarillo
intermitente y luego a amarillo. Se volverá a
encender el proyector si se (re)activa al menos
una fuente. La función de apagado puede
desactivarse en el menú. Véase DPMS en el
submenú CONFIGURACIÓN.

Para apagar el proyector, pulse firmemente dos
veces el botón POWER del teclado o del
mando a distancia (para confirmar que
realmente desea apagar el aparato). El
indicador STATUS pasará de verde a amarillo
intermitente y luego a amarillo al apagarse.

No se puede encender el aparato cuando el
indicador STATUS está amarillo intermitente.
Espere a que se quede en amarillo fijo.

UTILISATION DU PROJECTEUR

Après l'installation, allumez tous les appareils.

Pour allumer le projecteur, appuyez fermement
sur le bouton POWER du clavier ou de la
télécommande. Le voyant STATUS passera de
jaune à vert une fois l'appareil allumé.

Si le voyant est jaune clignotant, attendez qu'il
cesse de clignoter.

Quand une seule source est connectée, le
projecteur la détecte automatiquement. Si
plusieurs sources sont connectées, le
projecteur recherche la source active suivante
conformément à la liste ci-dessous, si toutefois
BALAYAGE SOURCES, dans le sous-menu
INSTALLATION est réglé sur ON (voir
description du système de menus).

- VGA 1
- VGA 2
- DVI-D
- Component
- S-Video
- Composite Video

Sélectionner la source parmi celles disponibles
en enfonçant le bouton SOURCE sur le clavier
ou la télécommande. Seules les sources
actives seront affichées.

Si aucune source n'est active, les messages de
recherche s'afficheront à l'écran.

Si aucune source n'est active pendant un long
laps de temps, le projecteur passera sur le
mode Standby si le DPMS (économie
d'énergie) est réglé sur ON dans le sous-menu
INSTALLATION. Le voyant STATUS passera du
vert au jaune clignotant, puis restera jaune. Le
projecteur se rallumera quand au moins une
source sera (ré)activée. La fonction d'arrêt peut
être désactivée dans le menu. Voir DPMS dans
le sous-menu INSTALLATION.

Pour éteindre le projecteur, appuyez
fermement deux fois (pour confirmer que vous
voulez arrêter l'appareil) sur le bouton POWER
du clavier ou de la télécommande. Le voyant
STATUS passera de vert à jaune clignotant,
puis au jaune fixe une fois l'appareil éteint.

Vous ne pouvez pas allumer l'appareil quand le
voyant STATUS clignote en jaune. Attendez
que le voyant jaune cesse de clignoter.

USING THE PROJECTOR

After setting-up, switch on all equipment.

To switch the projector on, firmly press the
POWER button on the keypad or the remote
control. The STATUS indicator will turn from
yellow to green when the unit is switched on.

If the STATUS indicator is flashing yellow,
please wait until it turns permanent yellow.

When only one source is connected, the
projector will auto-detect that source. If more
sources are connected, the projector will
search for the next active source according to
the following list, provided that SOURCE
SCAN is set to ON in the SET UP sub menu
(see description of menu system):

- VGA 1
- VGA 2
- DVI-D
- Component
- S-Video
- Composite Video

Select between the sources by pressing the
SOURCE buttons on the keypad or the remote
control. Only sources that are active will be
displayed.

If no source is active, searching messages will
appear on the screen.

If no source is active for a long time, the
projector will go in standby mode if DPMS
(power save) is set to ON in the SET UP sub
menu. The STATUS indicator will turn from
green to flashing yellow, then yellow. The
projector will be switched back on if at least
one source is (re)activated. The power-down
function can be disabled in the menu. See
DPMS in the SET UP sub menu.

To switch the projector off, firmly press the
POWER button on the keypad or the remote
control twice (to confirm that you really want to
switch off the unit). The STATUS indicator will
turn from green to flashing yellow, then yellow
when switched off.

You may not switch the unit on while the
STATUS indicator is flashing yellow. Please
wait until the indicator is permanent yellow.

BENUTZUNG DES PROJEKTORS

Sobald der Aufbau beendet ist, schalten Sie
alle Geräte ein.

Zum Einschalten des Projektors drücken Sie
fest auf die POWER-Taste auf dem Tastenfeld
oder der Fernbedienung. Sobald das Gerät
eingeschaltet ist, schaltet die STATUS-Anzeige
von gelb auf grün um.

Sollte die STATUS-Anzeige gelb blinken,
müssen Sie warten, bis sie als gelbes
Dauerlicht leuchtet.

Wenn nur eine Quelle angeschlossen ist,
erkennt der Projektor diese automatisch. Sind
mehrere Quellen angeschlossen, sucht der
Projektor die folgende aktive Quelle nach der
nachstehenden Liste, vorausgesetzt die Option
SOURCES SCAN ist im Untermenü
EINSTELLUNGEN auf ON gestellt (siehe die
Beschreibung des Menüsystems):

- VGA 1
- VGA 2
- DVI-D
- Component
- S-Video
- Composite Video

Wählen Sie die entsprechende Quelle mit Hilfe
der Taste SOURCE auf dem Tastenfeld bzw.
der Fernbedienung. Es werden nur aktive
Quellen angezeigt.

Ist keine Quelle aktiv, erscheint auf dem
Bildschirm die Suchmeldung.

Ist über eine längere Zeit keine Quelle aktiv,
geht der Projektor in den Standby-Modus über,
wenn DPMS (Stromsparfunktion) im
Untermenü EINSTELLUNGEN auf ON gesetzt
ist. Die STATUS-Anzeige wechselt von grün auf
gelb blinkend und anschließend auf gelb. Der
Projektor wird wieder angeschaltet, sobald
mindestens eine Quelle (re) aktiviert wird. Die
Stromsparfunktion kann im Menü deaktiviert
werden. Siehe DMPS im Untermenü
EINSTELLUNGEN.

Zum Ausschalten des Projektors zweimal fest
auf die Taste POWER auf dem Tastenfeld bzw.
der Fernbedienung drücken (zur Bestätigung,
dass Sie das Gerät wirklich ausschalten
möchten). Die STATUS-Anzeige wechselt von
grün auf gelb blinkend und dann auf gelb,
wenn das Gerät ausgeschaltet ist.

Das Gerät kann nicht angeschaltet werden,
wenn die STATUS-Anzeige gelb blinkt. Bitte
warten, bis ein gelbes Dauerlicht erscheint.

english

deut

sch

francais

esp

añol

norsk

O

BRUK AV PROJEKTOREN

Skru på enhetene etter at de er koblet
sammen.

Skru på projektoren ved å trykke bestemt på
POWER knappen. STATUS indikatoren skifter
fra gult til grønt når den skrus på.

Hvis STATUS indikatoren blinker gult må du
vente til den skifter til fast gult lys.

Dersom kun en kilde er tilkoblet, vil denne
kilden automatisk velges. Hvis flere kilder er
tilkoblet, vil projektoren søke seg fram til den
første aktive kilden i følge nedenstående liste,
forutsatt at SOURCE SCAN er på i SET UP
undermenyen (se beskrivelsen av
menysystemet):

- VGA 1
- VGA 2
- DVI-D
- Component
- S-Video
- Composite Video

Velg mellom kildene (inngangene) ved å
trykke på SOURCE knappene på tastaturet
eller fjernkontrollen. Kun aktive kilder vises.

Meldinger kommer opp på skjermen for de
kilder som ikke er tilkoblet.

Hvis det ikke er aktive kilder tilkoblet over
lengre tid, vil projektoren gå i hvilemodus
dersom strømsparingsfunksjonen (DPMS) er
satt på i SET UP undermenyen. STATUS
indikatoren skifter da fra grønt til blinkende
gult, deretter fast gult. Projektoren skrus på
igjen når minst en kilde (re)aktiviseres.
Strømsparerfunksjonen (DPMS) kan skrus av
i SET UP undermenyen.

Skru av projektoren ved å trykke bestemt på
POWER knappen på tastaturet eller
fjernkontrollen to ganger (for å bekrefte at du
virkelig vil skru av). STATUS indikatoren vill
skifte fra grønt til blinkende gult, deretter
permanent gult når enheten går i hvilemodus.

Enheten kan ikke umiddelbart skrus på igjen
så lenge STATUS indikatoren blinker gult.
Vennligst vent til indikatoren er permanent
gult før du skrur på igjen.

it

aliano

Advertising