Enerpac PR-Series Electric Benutzerhandbuch
Seite 7
PRS Series spacers allow additional fine adjustment of the
extension stack height. They may be used alone or in conjunction
with PRE Series extensions.
Table 4 - PRS Series Spacers (optional accessories)
Spacer Model
Thickness (each)
inches
mm
PRS1
1
25
PRS2
2
51
PRS3
3
76
PRS4 Spacer Set
Set includes PRS1, PRS2 and PRS3 (1 each).
WARNING: Never exceed the maximum additional
stack height for your jack model. Refer to Table 5 for
additional information.
WARNING: Failure to observe the following instructions
could allow load to shift or drop. Serious personal injury
and/or property damage may result.
When using PRE Series extensions and/or PRS Series spacers,
always obey the following rules:
• For loads up to 60 tons [54 metric tons]: Any two PRE Series
extensions may be included in the stacking arrangement,
provided that the maximum stack height (See Table 5) is not
exceeded and the following exceptions are observed:
1) Jack models PREMB06014L, PREMI06014L and
PREME06014L: Only one PRE18 extension can be included
in the stacking arrangement.
2) All jack models ending in “16L”: Only one PRE11,
PRE14 or PRE18 extension can be included in the stacking
arrangement.
3) All jack models ending in “27L”: Extensions PRE14 and
PRE18 cannot be included in the stacking arrangement.
These extensions are designed for short stroke jacks only
(models ending in “14L” and “16L”).
• For loads over 60 tons [54 metric tons], or strokes over 14
inches [356 mm]: Only one PRE Series extension and one PRS
Series spacer can be included in the stacking arrangement.
• Never exceed 3 inches [76 mm] in total spacer height.
• Never exceed the maximum additional stack height for your
jack model. Refer to Table 5, dimension “X”.
Table 5 - Maximum Additional Stack Height Using
Optional PRE Series Extensions and PRS Series Spacers
Jack
Model
Maximum Additional Stack
Height (dimension “X”)
X
inches
mm
PREM_06014L
32
813
PREM_06027L
11
279
PREM_10016L
21
533
PREM_10027L
11
279
PREM_15016L
21
533
PREM_15027L
11
279
PREM_20016L
21
533
PREM_20027L
11
279
Note: Fifth letter of model will be B, E, I, G, W, J
or R, depending on jack electrical configuration.
Important: Refer to
Table 5 for maximum
additional stack height
information.
PRS Series Spacer
(see Table 4)
Load Cap
(see Table 6)
PRE Series
Extension
(see Table 3)
Cylinder Rod
Figure 5, Extension and Spacer Installation (typical)
5.7 Load Caps
A non-swivel load cap is included with the jack as standard
equipment. A swivel load cap is available as an optional
accessory. Refer to Table 6 for a list of load cap model numbers.
IMPORTANT: Use a swivel load cap to properly engage angled
lifting points. A swivel load cap should always be used when the
amount of misalignment between the standard load cap and the
lifting point is too large to be compensated for by use of plywood
or other suitable high-friction compression material alone.
Table 6 - Load Caps
Jack Model
Load Cap Model Numbers
Non-Swivel Load
Cap (standard)
Swivel Load Cap
(optional accessory)
PREM_06014L
42208E
PRTS60
PREM_06027L
PREM_10016L
42208E
PRTS60
PREM_10027L
PREM_15016L
42208E
PRTS150
PREM_15027L
PREM_20016L
42208E
PRTS200
PREM_20027L
Note: Fifth letter of model will be B, E, I, G, W, J or R, depending on
jack electrical configuration.
7