HEIDENHAIN TNC 407 (243 020) Technical Manual - Handbuch (Seite 749)

13-8
TNC 407/TNC 415/TNC 425 Stichwortverzeichnis 11.97
M
M-Funktionen ......................................... 4-139
Mittenversatz.......................................... 4-178
MOD (MODULO) ................................... 7-70
MOD [ ] (MODULO [ ]) ........................... 7-86
modaler Zyklus-Aufruf ............................ 4-162
Modul 9000/9001 ................................... 7-136
Modul 9010/9011/9012 .......................... 7-137
Modul 9020/ 9021/ 9022 ........................ 7-138
Modul 9031 ............................ 2-19; 5-5; 7-139
Modul 9032 ................................... 2-19; 7-140
Modul 9033 ................................... 2-23; 7-140
Modul 9035 .......................... 2-20; 2-22; 7-141
Modul 9036 ............................................ 7-144
Modul 9040/9041/9042 .......................... 7-145
Modul 9041 .............................................. 2-19
Modul 9050 ............................................ 7-147
Modul 9051 ............................................ 7-148
Modul 9052 ............................................ 7-149
Modul 9053 ............................................ 7-150
Modul 9054 ............................................ 7-150
Modul 9070 ................................. 4-141; 7-151
Modul 9071 ................................. 4-141; 7-152
Modul 9080 ...................... 4-141; 7-114; 7-152
Modul 9081 ................................. 4-141; 7-153
Modul 9082 ...................... 4-141; 7-114; 7-153
Modul 9083 ........................ 2-19; 4-141; 7-155
Modul 9090 ............................................ 7-157
Modul 9093 .............................................. 2-19
Modul 9093/9094 ................................... 7-158
Modul 9094 .............................................. 2-19
Modul 9095 ............................................ 7-161
Modul 9100 ............................................ 7-163
Modul 9101 ............................................ 7-163
Modul 9102 ............................................ 7-164
Modul 9103 ............................................ 7-165
Modul 9104 ............................................ 7-165
Modul 9105 ............................................ 7-167
Modul 9106 ............................................ 7-167
Modul 9107 ............................................ 7-168
Modul 9110 ............................................ 7-169
Modul 9111 ............................................ 7-170
Modul 9120 ............................................ 7-171
Modul 9121 ............................................ 7-172
Modul 9122 ............................................ 7-172
Modul 9123 ............................................ 7-173
Modul 9130 ............................................ 4-275
Modul-Aufruf (CM)................................ 7-107
Modul-Ende ............................................ 7-110
Modultechnik............................................ 7-17
MSB............................................................ 8-6
Multiplikationsfaktor ................................. 4-72
MULTIPLIZIEREN (x) .............................. 7-68
MULTIPLIZIEREN [ ] (x[ ]) ....................... 7-85
N
N ...............................................................8-18
Näherungs-Schalter ................................4-223
NC-Software ...............................................2-8
NC-Start ..................................................4-174
Negative Lose...........................................4-23
Nichtlineare Achsfehler-Kompensation ....4-27
Nichtlineare Achsfehler-Korrektur...........7-161
nichtlinearen Kennlinie............................4-138
Normalen-Richtung .................................4-181
NOT-AUS-Routine........................4-189; 4-262
Nullpunkt-Korrektur.................................4-221
Nullpunkt-Tabelle .....4-150; 4-151; 7-157; 8-18
Nullpunkt-Verschiebung..........................4-132
Null-Referenzmarke ..................................4-53
O
O (OR).....................................................7-57
O[ ] (OR [ ]...............................................7-80
ODER (O) ................................................7-57
ODER [ ] (O[ ] ..........................................7-80
ODER NICHT (ON)..................................7-59
ODER NICHT [ ] (ON[ ])...........................7-80
Offset-Abgleich.2-24; 4-75; 4-77; 4-104; 4-274
ON (OR NOT)..........................................7-59
ON[ ] (OR NOT [ ])...................................7-80
Operand ....................................................7-16
Operandenteil ...........................................7-16
Operanden-Übersicht ...............................7-18
Orientierung............................................4-106
Oszilloskop .............................................11-17
Oszilloskop-Funktion.................................2-22
OUTPUT BINARY CODE 0001 .................7-10
Overflow .................................................7-123
Override ................................2-19; 2-20; 4-138
OVWR (OVERWRITE)...........................7-116