HEIDENHAIN TNC 407 (243 020) Technical Manual - Handbuch (Seite 752)

11.97
TNC 407/TNC 415/TNC 425 Stichwortverzeichnis 13-11
S
S ............................................................... 8-18
S (SET) .................................................... 7-48
S-Analogspannung für Getriebestufen ..... 4-97
Satznummern-Schrittweite..................... 4-151
Satzverarbeitungszeit ................................. 2-3
Satzvorlauf ..................................... 2-20; 4-149
Schachtelungstiefe ..................................... 9-2
Schiebe-Befehle ....................................... 7-93
SCHIEBEN LINKS (<<) ........................... 7-93
SCHIEBEN RECHTS (>>) ....................... 7-94
Schleppabstand .................... 4-68; 4-75; 4-265
Schlüsselzahl ............... 2-19; 4-31; 4-77; 4-152
................................................. 4-258; 5-4; 7-6
Schmier-Impuls......................................... 4-19
Schneidmaschinen ................................. 4-275
Schneller PLC-Eingang .................... 2-19; 4-83
Schnittstelle................................................ 8-3
SCHNITTSTELLE BELEGT........................ 8-48
Schreiben Wörter ................................... 7-138
Schrittmaß .............................................. 4-209
Schutzklasse............................................. 3-13
Schwenkachsen ....................................... 4-41
Schwester-Werkzeug ............................. 4-227
Schwingungen in Normalen-Richtung .... 4-188
Schwingungs-Amplitude......................... 4-181
S-Code .................................................... 4-104
S-Code für minimale Drehzahl ................ 4-104
S-Code-Tabelle........................................ 4-105
SE 510 ...................................................... 3-39
SELECT M/I/O/T/C .................................... 7-11
Sende- Empfangseinheit .......................... 3-39
Seriell.......................................................... 8-4
SETZE (S)................................................ 7-48
SETZE NICHT (SN).................................. 7-50
Siebkondensator....................................... 3-16
Signalbezeichnung.................................... 8-12
Signalperiode .............................................. 4-6
SN (SET NOT) ......................................... 7-50
Softkey ................................................... 4-164
Softkeys.................................................... 3-67
Software ..................................................... 2-8
Software-Endschalter ........... 4-16; 4-53; 4-265
Software-Handshake .................................. 8-9
Software-Modul.................. 2-10; 4-180; 4-189
Software-Option ....................................... 2-10
Software-Tausch....................................... 2-15
Software-Typ .............................................. 2-8
Soll-Drehzahl............................................. 4-95
Sollwert-Ausgang ..................................... 3-32
Sonderfunktionen ................................... 4-275
Sonderwerkzeug....................................... 2-19
S-Override................................................. 4-99
Spannungsschritte.................................... 4-71
S
Speicher......................................................2-3
Speicher-Befehl ........................................7-36
Speicherfunktion für Achsrichtungs-Tasten
................................................................4-174
Speichern eines STRING (=) .................7-116
Speicher-Test..........................................4-154
Spindel in Position ..................................4-109
Spindel-Drehung links .............................4-101
Spindel-Drehung rechts ..........................4-101
Spindelnachlaufzeit .................................4-114
Spindel-Orientierung .............3-27; 4-94; 4-106
Spindel-Preset ........................................4-108
Spindelsteigungsfehler .............................4-27
Sprung (JP) ...........................................7-105
Sprung-Befehle .......................................7-105
Sprungmarke (LBL) ...............................7-110
Stack holen (PL) ....................................7-101
Stack holen (PLL) ..................................7-102
Stack holen (PLW) ................................7-102
Stack laden (PS)....................................7-100
Stack laden (PSL)..................................7-101
Stack laden (PSW) ................................7-102
Stack-Operationen ..................................7-100
Standard-Datenübertragungsprotokoll8-10; 8-28
Standzeit .................................................4-227
Standzeit-Zähler ......................................4-227
START DISPLAY .......................................7-11
START TRACE ..........................................7-11
Start-Bit.......................................................8-6
Status lesen ............................................7-141
Status schreiben.....................................7-144
Status-Abfrage (RPLY) ............................7-124
Status-Fenster ........................................4-134
Steckerbelegung X1, X2, X3, X4, X5.........3-25
Steckerbelegung X10 ...............................3-36
Steckerbelegung X12 ...............................3-37
Steckerbelegung X6, X7 ...........................3-26
Steckerbelegung X8 .................................3-32
Steckplätze ...............................................2-13
Steuer- und Meldeleitungen .....................8-11
Steuerung ist betriebsbereit ...................4-120
Stillstand-Überwachung............................4-87
STOP DISPLAY .........................................7-11
STOP TRACE ............................................7-11
Stop-Bit .......................................................8-6
Störquellen..................................................3-9
STRING-Akku..........................................7-114
String-Bearbeitung ..................................7-151
STRING-Speicher ....................................7-114
STRING-Verarbeitung .............................7-114
Strobe .......................................................7-23
STROMUNTERBRECHUNG ...................4-155
Stromversorgung ......................................3-16