FMC Corporation - Talstar 80 - Handbuch (Seite 74)

Troubleshooting Proline Promass 80 PROFIBUS PA
74
380 S: UPPER FREQ. LIM
$: # 380 0x0F BAD Device Failure Constant Frequence limit 2 Cause:
The measuring tube oscillation frequency is outside
the permitted range.
Causes:
Measuring tube damaged
Sensor defective or damaged
Remedy:
Contact your Endress+Hauser service organization.
381 S: FLUIDTEMP.MIN.
$: # 381 0x10
0x11
0x12 BAD Sensor Failure O.K.
Low
High
Fluid Temperature
Min. Cause:
The temperature sensor on the measuring tube is
likely defective.
Remedy:
Check the following electrical connections before
you contact your Endress+Hauser service
organization:
• Verify that the sensor signal cable connector is
correctly plugged into the amplifier board
• Remote version: Check sensor and transmitter
terminal connections No. 9 and 10
→ Page 29 ff.
382 S: FLUIDTEMP.MAX.
$: # 382 0x10
0x11
0x12 BAD Sensor Failure O.K.
Low
High
Fluid Temperature
Max.
383 S: CARR.TEMP.MIN
$: # 383 0x10
0x11
0x12 BAD Sensor Failure O.K.
Low
High
Carrier
Temperature Min. Cause:
The temperature sensor on the carrier tube is likely
defective.
Remedy:
Check the following electrical connections before
you contact your Endress+Hauser service
organization:
• Verify that the sensor signal cable connector is
correctly plugged into the amplifier board
• Remote version: Check sensor and transmitter
terminal connections No. 11 and 12
→ Page 29 ff.
384 S: CARR.TEMP.MAX
$: # 384 0x10
0x11
0x12 BAD Sensor Failure O.K.
Low
High
Carrier
Temperature Max.
385 S: INL.SENS.DEF.
$: # 385 0x10
0x11
0x12 BAD Sensor Failure O.K.
Low
High
Inlet Sensor Defect Cause:
One of the measuring tube sensor coils (inlet or
outlet) is likely defective.
Remedy:
Check the following electrical connections before
you contact your Endress+Hauser service
organization:
• Verify that the sensor signal cable connector is
correctly plugged into the amplifier board
• Remote version: Check sensor and transmitter
terminal connections No. 4, 5, 6, 7.
386 S: OUTL.SENS.DEF.
$: # 386 0x10
0x11
0x12 BAD Sensor Failure O.K.
Low
High
Outlet Sensor
Defect
387 S: SEN.ASY.EXCEED
$: # 387 0x10
0x11
0x12 BAD Sensor Failure O.K.
Low
High
Sensor Asymmetry
Exceeded
388 S: AMP. FAULT
$: # 388 0x0F BAD Device Failure Constant Amplifier failure Cause:
Amplifier error
Remedy:
Contact your Endress+Hauser service organization. 389 S: AMP. FAULT
$: # 389 0x0F BAD Device Failure Constant Amplifier failure
390 S: AMP. FAULT
$: # 390 0x0F BAD Device Failure Constant Amplifier failure
No. Device status message
(local display)
PROFIBUS measured value status
Extended
diagnostic
message in the
PROFIBUS
master
Cause/remedy (spare part
→ Page 80 ff.)
Q
u
a
lit
y co
de (H
EX
)
M
e
asured va
lue st
atus
Qua
li
ty st
a
tus
Qu
ality
substatus
Li
m
its