HEIDENHAIN TNC 407 (243 020) Technical Manual - Handbuch (Seite 748)

11.97
TNC 407/TNC 415/TNC 425 Stichwortverzeichnis 13-7
L
L....................................................... 7-40; 8-18
L (LOAD)...................................... 7-36; 7-115
LADE (L) ................................................. 7-36
LADE BYTE (LB) ..................................... 7-41
LADE DOPPELWORT (LD) ..................... 7-41
LADE NICHT (LN) ................................... 7-38
LADE WORT (LW) .................................. 7-41
LADE ZWEIER-KOMPLEMENT (L---) ...... 7-40
Lade-Befehl .............................................. 7-36
LADEN (L)............................................. 7-115
Lageabweichung ...................................... 4-71
Lageregelkreis .......................................... 4-65
Lageregelung............................................ 4-65
Landessprache ........................................... 2-8
Längenmeßsysteme................................. 3-24
Längenmessung ......................................... 4-6
Laser....................................................... 4-275
LB (LOAD BYTE)..................................... 7-41
LBL (LABEL) ......................................... 7-110
LD (LOAD DOUBLE WORD) .................. 7-41
LE 407 ...................................................... 3-74
LE 415 ............................................... 3-4; 3-75
LE 415 E ..................................................... 3-4
Leistungsaufnahme .................................. 3-16
Lesen Wörter.......................................... 7-137
Lineare Achsfehler-Kompensation ........... 4-26
LN (LOAD NOT)...................................... 7-38
LOGIC DIAGRAM ............................ 7-11; 7-12
Logik-Diagramm ....................................... 7-11
Logik-Einheit ............................................... 3-4
Logische Vergleiche ............................... 7-119
Logische Verknüpfungen.......................... 7-53
lokal ............................................................ 9-4
lokale Q-Parameter ..................................... 9-4
Look Ahead............................... 2-3; 2-24; 4-82
Löschbare Fehlermeldung ...................... 4-120
Löschen der Status-Anzeige................... 4-140
Lose-Kompensation.................................. 4-23
LSB ............................................................. 8-6
LSV/2 ...................................................... 7-169
LSV/2 TOOL BOX ..................................... 8-46
LSV/2-Protokoll ......................................... 8-46
LSV2/Protokol ........................................... 2-24
Luftfeuchtigkeit ........................................ 3-10
LW (LOAD WORD)................................. 7-41
M
M ..............................................................8-18
M03 ......................................4-96; 4-97; 4-139
M04 ......................................4-96; 4-97; 4-139
M05 ......................................4-96; 4-97; 4-139
M06 ........................................................4-161
M08 ........................................................4-139
M09 ........................................................4-139
M101 ......................................................4-227
M103 ......................................................4-161
M105 ......................................................4-162
M106 ......................................................4-162
M109 ........................................................4-81
M110 ........................................................4-81
M111 ........................................................4-81
M112 ........................................................4-82
M114 ........................................................4-48
M124 ........................................................4-82
M19 ........................................................4-106
M200 bis M204 ......................................4-275
M89 ........................................................4-161
M90 ...............................................4-81; 4-181
M91 ..........................................................4-53
M92 ..........................................................4-53
Mäander ......................................4-180; 4-182
magnetische Störfelder ............................3-13
Manual Operation ...................................4-149
Manuel Operation ...................................4-148
Maschinen-Achsen .....................................4-6
Maschinen-Bedienfeld ............................4-174
Maschinen-Nullpunkt2-18; 4-16; 4-63; 4-126; 4-127
Maschinen-Parameter ............2-22; 2-23; 8-18
Maschinen-Parameter lesen...................7-140
Maschinen-Parameter überschreiben.....7-139
Maschinen-Parameter?...............................5-2
Maschinen-Referenzpunkt......................4-127
Masse .........................................................2-7
Maßfaktor ...............................................4-147
Maßfaktor achsspezifisch.........................2-22
Maßstab-Nullpunkt .................................4-126
max. Stromaufnahme ...............................3-16
maximale Spindel-Drehzahl ......................4-97
Maximaler Meßweg ...............................4-177
ME ............................................................8-28
ME\: BAND-ENDE ...........................8-48; 8-49
MEGA-PROMMER ...................................7-28
Merker ...............................................6-1; 7-18
Meßschritt ................................................3-24
Meßsystem <Achse> defekt .....................4-9
Meßsystem-Anschluß ..............................3-28
Meßsysteme .....................................3-24; 4-6
Meßsystem-Eingänge ..............................3-25
Meßsystem-Überwachung.........................4-9