HEIDENHAIN TNC 407 (243 020) Technical Manual - Handbuch (Seite 750)

11.97
TNC 407/TNC 415/TNC 425 Stichwortverzeichnis 13-9
P
P ............................................................... 8-18
P.ABST ........................................ 4-180; 4-183
PA 110 ............................. 3-5; 3-18; 3-80; 4-32
Paletten-Datei ......................................... 7-157
Paletten-Tabelle ............................. 4-150; 8-18
Parallel ........................................................ 8-4
Parallelbetrieb ............................................. 2-4
Paritätsbit.................................................... 8-6
Paritätsprüfung ........................................... 8-7
PASS OVER REFERENCE ........................ 4-53
Pendelspannung ..................................... 4-101
PL (PULL).............................................. 7-101
PL 400 ............................. 3-4; 3-17; 3-60; 3-78
PL 410 .................................. 3-62; 3-79; 4-206
Platz-Codierung....................................... 4-228
Platz-Nummer.............................. 4-228; 4-231
Platz-Tabelle................................... 4-223; 8-18
PLC
ERROR 4-142
PLC Analogplatine ...................................... 3-5
PLC EDIT ...................................... 5-5; 7-6; 7-7
PLC RUN .................................................... 5-5
PLC-Achsen ................. 2-22; 2-24; 4-38; 7-171
PLC-Ausgang ............................................ 3-57
PLC-Ausgänge Technische Daten ............ 3-54
PLC-Betrieb ................................................ 7-6
PLC-Datenschnittstelle ............................. 8-47
PLC-Dialog ........................ 4-152; 7-115; 7-119
PLC-Durchlauf............................................. 7-6
PLC-Eingänge .................................. 3-56; 7-27
PLC-Eingänge Technische Daten ............. 3-54
PLC-Eingänge/-Ausgänge ......................... 3-53
PLC-EPROM ............................................. 2-17
PLC-ERROR............................................ 7-115
PLC-Fehlermeldung ................................ 4-142
PLC-Fehlermeldungen .............................. 2-19
PLC-Fenster...................... 4-141; 7-114; 7-152
PLC-Funktionen .......................................... 7-6
PLC-Hauptmenü ......................................... 7-7
PLC-Leistungsplatine.................................. 3-5
PLC-Positioniermodul ............................... 10-2
PLC-Positionierung .......................... 4-35; 4-53
PLC-Positionierungen ............................... 2-19
PLC-Programm ......................................... 8-18
PLC-Software ........................................... 2-13
PLC-Zykluszeit ............................................ 7-6
PLL (PULL LOGICACCU) ...................... 7-102
PLW (PULL WORDACCU).................... 7-102
PNT......................................................... 4-189
POCKET TABLE...................................... 4-223
Polarität der S-Analogspannung ............... 4-95
Polarität der Sollwert-Spannung ................. 4-8
POSITIONIER-FEHLER ........... 4-77; 4-84; 4-85
P
Positionier-Fenster....................................4-87
Positionier-Fenster der Werkzeugachse.4-118
Positionier-Fenster für Spindel ...............4-108
Positionier-Modul......................................10-2
Positioniermodul .......................................8-20
Positions-Anzeige ...................................4-134
Positions-Anzeige bei Drehachsen .........4-135
Positions-Überwachung............................4-84
Positionswerte..........................................2-20
Positive Lose ............................................4-23
PROGRAMM NICHT VOLLSTAENDIG8-48; 8-49
PROGRAMM NICHT VORHANDEN .........8-50
PROGRAMM UNVOLLSTAENDIG ...........8-50
Programm-Aufbau ....................................7-16
Programm-Erstellung ................................7-16
Programmierplatz ...................................4-153
Programmierte Drehzahl...........................4-95
Programmlauf-Ende ................................4-154
Programmlauf-Halt..................................4-161
Programm-Strukturen .............................7-127
PS (PUSH).............................................7-100
PSL (PUSH LOGICACCU) .....................7-101
PSW (PUSH WORDACCU)...................7-102
Pt 100 ..............................3-5; 3-18; 3-55; 4-32
Puffer-Batterie ..........................................3-18